... methods of exploration, such as SPT, CPT, etc. to establishstratification of the subsurface materials, the profile of the top of bedrock and bedrock quality, depth togroundwater, limits of types of ... be unsuitable for fieldverification of nominal axial resistance of soft silts orclays where a large amount of setup is anticipatedand it is not feasible to obtain dynamicmeasurement of pile ... right of way restrictions,proximity of adjacent structures, andschedule constraints Identify areas of geologic concern on the siteand potential variability of local geology Identify areas of...
... lowerportion of the shaft.The value of is often considered to vary as afunction of Su. Values of for drilled shafts arerecommended as shown in Equations 2 and 3,based on the results of back-analyzed, ... bottom of the base or over thedepth of penetration of the drilled shaft in the foundingstratum.The value of Numay be assumed to vary linearlyfrom 0.0 at Db/Dp= 0.75 to a value of 8.0 ... distance of 1.5B above the top of the weaker layer to the baseresistance of the weaker layer at the top of the weakerlayer.C10.8.3.5.3The distance of 1.5B represents the zone of influence for general...
... types of cement for various types of sulfate exposure.For prestressed concrete, ACI 318recommends a maximum water-soluble chloride ion of 0.06 percent by weight of cement.Cathodic protection of ... RESISTANCE OF PILE GROUPS INCOMPRESSIONFor pile groups in clay, the nominal axialresistance of the pile group shall be taken as thelesser of: The sum of the individual nominal resistances of each ... shear strength of clays (KSF)nh= rate of increase of soil modulus with depthfor sands as specified in Table 10.4.6.3-2(KSI/FT)10.7.4 Extreme Event Limit StateThe provisions of Article 10.5.5.3...
... the zone of overbreak or fracturing.Evaluation of seepage forces and hydraulicgradients should be performed as part of the design of foundations that will extend below the groundwater table. ... bottom of the footingto 1.5B below the bottom of the footing.B = footing width (FT)Cwq, Cw= correction factors to account for thelocation of the ground water table asspecified in Table ... for timing of closure pours as a function of settlement, simplesupport of spans and/or periodic jacking of bearingsupports.Where laboratory test results are expressed interms of void ratio,...
... methods of exploration, such as SPT, CPT, etc. to establishstratification of the subsurface materials, the profile of the top of bedrock and bedrock quality, depth togroundwater, limits of types of ... (KSI)nh= rate of increase of soil modulus with depthas defined in Table C2 (KSI/FT)z = depth in feet below the ground surface (FT) Table C10.4.6.3-2 – Rate of increase of SoilModulus with ... subsurfaceconditions observed, the intent ofTable 1 regardingthe minimum level of exploration needed should becarried out. The depth of borings indicated in Table 1performed before or during design...
... [NWAN96]__________Tilburg University, Tilburg, TheNetherlands, the 9th of July 1996 1Intelligent Software Agents on the Internet Tableof Contents ... Intelligent Software Agents on theInternet:an inventory of currently offeredfunctionality in the informationsociety & a prediction of (near-)future developmentsby ... Hermans__________"[ ] Agents are here tostay, not least because of their diversity, their widerange of applicability andthe broad spectrum of companies investing inthem. As we move furtherand further...
... German TM TABLE OF CONTENTS Field 17: GermanPART 1: GENERAL INFORMATION ABOUT THE AEPA AND TEST PREPARATIONAN OVERVIEW OF THE AEPA 1-1Test Development ProcessCharacteristics of the ... adequacy of the information presented, including the number of ideas, thedevelopment of ideas, and the depth and specificity of supporting detailsã COHERENCE: the organization and clarity of the ... understanding of the main idea or details in a spoken passage, atelephone message, a public address announcement, a sequence of steps described in a set of oraldirections, a stated cause or effect of...
... LossMaximum insertion loss is the upper limit of insertion loss for the coupler and applies over the entirewavelength range specified in the bandpass.Typical Insertion LossTypical insertion ... Cycling:Corning SMF-280.900 mm1.0 Log2N (where N = number of channels)0.5 dB maximum(see table below)(see table below)< -55 dB55 dB(see table below).45 kg (1.0 lb.) maximum for .250 mm and ... 15.8SplitterNumberSplitterTypeSplitterRatioMaximumInsertion Loss*Typical Insertion Loss** Does not include connector loss. See table on the following page or call ADC Technical Assistance Center, 1-800-366-3891.Maximum Insertion...
... COMPLETE TABLEOFCONTENTS AND GLOSSARY Lesson 11: Passwords11.0 Introduction11.1 Types of Passwords11.1.1 Strings of Characters11.1.2 Strings of Characters plus a token11.1.3 Biometric Passwords ... securityorganization in the UK.9 COMPLETE TABLEOFCONTENTS AND GLOSSARY COMPLETE TABLE OF CONTENTS ANDGLOSSARY social engineering – The act of obtaining or attempting to obtain otherwise ... Biometric Passwords 11.2 History of Passwords11.3 Build a Strong Password11.4 Password Encryption11.5 Password Cracking (Password Recovery)11.6 Protection from Password CrackingLesson 12: Legalities...
... tray with chip5. Select number of cable clamps (0-9)6. Select number of compression fittings (0-9)7. Select number of bonding grounding kits (0-9)8. Select number of radius limiters (0-9). Not ... connector on back of bulkhead)STđ Hybrid (STđ connector on front; SC connector on back of bulkhead) Multimode9D5YSinglemode2LF7NJE4PKX13Connector StyleNumber of Ports LoadedNumber ... Minneapolis, Minnesota USA 55440-1101Specifications published here are current as of the date of publication of this document. Because we are continuously improving our products, ADCreserves...
... Editor of the IEEE Transactionson Neural Networks. Andrew Kusiak is a Professor of Industrial Engineering at the University of Iowa, Iowa City. His interestsinclude applications of ... University of CalgaryCanada Nallan C. Suresh State University of New York at BuffaloU.S.A. University of GroningenThe Netherlands Wai Sum Tang The Chinese University of Hong KongChina ... affiliated with a number of major professional societies such as IEEE, ASME, SME,IIE, and their counterparts in Europe, Asia, and the rest of the world. The book is a source of newinformation for...
... Accountability Office (I) Office of Management and Budget (1) Office of the Chief Financial Officer Director, Planning and Accountability Division (1) Japan Export Investigation Report For Official ... 2005: GOJ conducted audits of 11 U.S. plants. AMS audited all of these establishments in advance of GOJ officials visit in order for them to observe actual production of product for Japan (as ... processed and distributed in Japan”. A final assessment of equivalency of the terms of the EV program would be the basis of Japan’s lifting of its ban on U.S. beef. August 8, 2005: USG assessed...