0

tài liệu học lái xe ô tô 2013

Tài liệu hộp số xe ô tô FORD FOCUS và FORD FIESTA

Tài liệu hộp số xe ô FORD FOCUS và FORD FIESTA

Cơ khí - Chế tạo máy

... actuator motor provides the holding torque. During disengagement the clutch actuator motor relaxes to it's rest position. When engaged the applied force is directed back into the transmission ... Identification (PID) Chart NOTE: The following general PID list may be of use to the technician when exercising output state control: Accessing PIDs PIDs PID Description 1stBLCK_GR_JMP 1st Gear...
  • 144
  • 1,981
  • 11
Tài liệu sửa chữa xe ô tô Renault 19 (Repair Manual) - P1

Tài liệu sửa chữa xe ô Renault 19 (Repair Manual) - P1

Cơ khí - Chế tạo máy

... discs must be changed if they are excessively scratched or worn.(2) Wheel cylinder with integral fixed compensator: in the event of a wheel cylinder or compensatorfunction fault: change the assembly, ... tabsBottleKit77 01 421 13577 01 422 752VARNISHAIR CONDITIONINGã Compressor oil ELF RIMA 100Fixed cubic capacity compressor oil SANDEN SP20Variable cubic capacity compressor oil SP10250...
  • 51
  • 1,838
  • 8
Tài liệu sửa chữa xe ô tô Renault 19 (Repair Manual) - P2

Tài liệu sửa chữa xe ô Renault 19 (Repair Manual) - P2

Cơ khí - Chế tạo máy

... of two bolts around the gearbox. 92903SCengines21-13 MANUAL GEARBOXESSpecial featuresGEAR CHANGE PATTERNThe gearboxes of the following types:JB0JB4JB2JB1JB3 5 forward gearsJB5 1 ... the gearbox with oil.21-28 MANUAL GEARBOXES5th speed linkage in situ21On the secondary shaft:Remove shouldered washer (64).PRG21.1Remove the fixed gear using tool B.Vi. 28-01-02-03 fitted ... 1007.88575RREFITTINGOn the secondary shaft:Put three drops of Loctite FRENBLOC on the fixedgear splines.Fit the fixed gear using tool B. Vi. 1175 and shoul-dered washer (64).93462RRemove tool B....
  • 140
  • 1,081
  • 6
Tài liệu sửa chữa xe ô tô Renault 19 (Repair Manual) - P3

Tài liệu sửa chữa xe ô Renault 19 (Repair Manual) - P3

Cơ khí - Chế tạo máy

... reconnected in their original positions. This is essential.30"X" TYPE BRAKING SYSTEMwith fixed compensator whichis integral with the wheel cylinder91563-3S"X" TYPE BRAKING SYSTEMwith...
  • 311
  • 1,065
  • 6
Tài liệu sửa chữa xe ô tô Renault 19 (Repair Manual) - P10

Tài liệu sửa chữa xe ô Renault 19 (Repair Manual) - P10

Cơ khí - Chế tạo máy

... inner rubbing stripC66-1 WINDOW SEALSRear door frame seal66ERemove the trim and the small fixed windowRemove:the seal, which is very fragile, using an extra-flatchisel. Free the rear section...
  • 10
  • 547
  • 1
Tài liệu đào tạo xe ô tô sonata 2011

Tài liệu đào tạo xe ô sonata 2011

Cơ khí - Chế tạo máy

... trí Tốc độ xe Tín hiệu vào từ cơ cấuChuyển từ chế độ( S  D + -D10kph or moreS(Lên số)S(Giảm số)- Giảm ga cho đến ki tốc độ xe (VS < 10kph) - Cho động cơ làm việc không tải khoảng ... Motor Company.Khái niêm: Xác nh c xe d ng trên d cđị đượ ừ Holds the brake pressure for 2sec when the slope is higher than 8%. Ch c n ng: Ch ng xe b trôi khi kh i hứ ă ành trên d ... tiếp : Tăng đặc tính của động cơ lên (13%), Giảm mức tiêu hao nhiên liệu 2%), Giảm sự độc hại của khí thải (50%)PHUN NHIÊN LiỆU TRƯC TIẾP (GDI) 45Introduction of YFCopyright  2009 All rights...
  • 55
  • 1,580
  • 20
ỨNG DỤNG CÔNG NGHỆ CAD/CAM ĐỂ THIẾT KẾ  CHẾ TẠO BƠM BEN LÁI XE Ô TÔ SCANIA

ỨNG DỤNG CÔNG NGHỆ CAD/CAM ĐỂ THIẾT KẾ CHẾ TẠO BƠM BEN LÁI XE Ô SCANIA

Cơ khí - Vật liệu

... Nhiệt độ nung 880 độ C, môi trường tôi là dầu khoáng vậtTôi : Nhiệt độ nung 880 độ C, môi trường tôi là dầu khoáng vật Ram : Nhiệt độ nung 250 độ C, môi trường tôi là không khí nénRam : Nhiệt ... đề tài tốt nghiệp ’’Trong báo cáo đề tài tốt nghiệp ’’ Ứng dụng công Ứng dụng công nghệ CAD/CAM để thiết kế chế tạo bơm ben lái xe nghệ CAD/CAM để thiết kế chế tạo bơm ben lái xe ... Nguyên công 2 11ĐỒ ÁN TỐT NGHIỆPĐỒ ÁN TỐT NGHIỆPĐề tài Đề tài :: ỨNG DỤNG CÔNG NGHỆ CAD/CAM ĐỂ THIẾT KẾ ỨNG DỤNG CÔNG NGHỆ CAD/CAM ĐỂ THIẾT KẾ CHẾ TẠO BƠM BEN LÁI XE Ô SCANIACHẾ...
  • 20
  • 785
  • 2

Xem thêm