... SEPIC
Index
http://ece-www.colorado.edu/~pwrelect/book/contents/TOC2.html (2 of 2) [25/04/2002 16:42:28]
Fundamentals of Power Electronics Table of Contents
Fundamentals of Power Electronics
R. W. Erickson
Table of Contents
Back
1. Introduction
1.1. ... design
http://ece-www.colorado.edu/~pwrelect/book/contents/TOC.html (6 of 11) [25/04/2002 16:42:25]
Fundamentals of Power Electronics Table of Contents Chapter titles only
Fundamentals of Power Electronics
R. W. Erickson
Table of Contents
Chapter ... of 11) [25/04/2002 16:42:25]
Fundamentals of Power Electronics
http://ece-www.colorado.edu/~pwrelect/book/copies.html (2 of 2) [25/04/2002 16:42:07]
Fundamentals of Power Electronics Table of...
... method, attempting to reduce the value χ
2
of a fit between a set of data
points
x[1 ndata]
,
y[1 ndata]
with individual standard deviations
sig[1 ndata]
,
and a nonlinear function dependent on
ma
coefficients
a[1 ... and
alamda
de-
creases by a factor of 10. If a step fails
alamda
grows by a factor of 10. You must call this
684
Chapter 15. Modeling of Data
Sample page from NUMERICAL RECIPES IN C: THE ART OF SCIENTIFIC COMPUTING ... even when they must be offered without proof.
Figure 15.6.1 shows the conceptual scheme of an experiment that “measures”
a set of parameters. There is some underlying true set of parameters a
true
that...
... aspect of any design. A wrong choice of
material may lead to failure, over or undersized product or expensive items. The
choice of materials is thus dependent on suitable properties of the ... arising
out of a defective product. Use of a factor of safety only in design does not
ensure its overall reliability.
Maintenance, cost and aesthetics
Maintenance and safety are often interlinked. ...
Instructional Objectives
At the end of this lesson, the students should have the knowledge of
• Basic concept of design in general.
• Concept of machine design and their types.
• Factors...
... that the state of stress
at a point can be given by six stress components only. It is important to
understand the implication of this state of stress at a point in the design of
machine elements ... loaded brass strut hinged at both ends is 1m long and is of a
square cross-section of sides 20mm. What should be the dimension of a
steel strut of the same length and subjected to the same axial ... aluminium shaft of
100mm diameter by a tubular steel shaft of the same outside diameter
transmitting the same torque and having the same angle of twist. Find the
inner radius of the steel bar...
... Overview ofData Modeling and
Database Design
8
Overview ofData Modeling and Database Design 8Ć5
Overview
When you create a database, you need to carefully consider ... design.
Database Design
Database design is just one of the stages of the development cycle. Through good
database design, you can achieve a reliable, high-performance system.
Challenges to Managing Data
There ... naming rules, and guidelines.
1
2
Overview ofData Modeling and Database Design 8Ć11
Data Model
Models are a cornerstone of design. Engineers build a model of a car before putting it
into production...
... several of the datastructures we examine
in this book.
While this use of generic programming can be quite useful, C# provides a
library of generic datastructures already ready to use. These data structures
are ... 2007 20:59
Preface
The study ofdatastructures and algorithms is critical to the development
of the professional programmer. There are many, many books written on
data structures and algorithms, ... ofdata structures
and algorithms using C#. The datastructures we use in this book are found
in the .NET Framework class library System.Collections. In this chapter, we
develop the concept of...
... be accomplished by adjusting the location of a
“fixed pivot.” That is, the second degree of freedom is obtained by moving a chosen
“fixed pivot” of a one-dof mechanism along either a straight or ... linkages
2. Degree of freedom: F = 1 (Change of stroke length will be accomplished by
adjusting the location of a fixed pivot.)
3. Joint types: revolute (R) and prismatic (P)
4. Number of prismatic ... kinematic
structures as given below:
RRRRRRR (Myard, Voss, Wachter and Reiger),
RRRPRRR,
RRPRPRR (Derby, S.W. Industries),
RPRRRPR,
RRPPPRR,
RPRPRPR.
Overall, a total of 12 kinematic structuresof C-V...
... The Three Principles ofData Center Infrastructure Design
Page 7
Deployment
The graphic below depicts a sample data center using ADC's comprehensive line ofdata center-grade
infrastructure ... Category 6
Page 3
The Three Principles ofData
Center Design
When you understand the three principles ofdata center
design, you are able to:
• Lower your total cost of ownership
• Support your future ... outside world,
huge streams ofdata are transferred to and from
equipment areas at extremely high data rates. The
infrastructure must consistently support the flow ofdata
without errors that...
... range of a linear transformation L of U into V is the set of vectors
v of V into which some vector u of U is mapped, i.e., the range of L is
defined as the set of v = Lu, for every vector u of U.Thekernel ... with
respect to the bases B
U
and B
V
is composed of the n real coefficients l
ij
of
the representation of the image of the jth vector of B
U
in terms of B
V
.
The notation introduced in eq.(2.10) ... {v
i
}
n
1
is called the dimension of V.Notethat
any set of n linearly independent vectors of V can play the role of a basis of
this space, but once this basis is defined, the set of real coefficients {α
i
}
n
1
for...
... assessment
of its risk?
Your firm, Agrico Products, is considering the purchase of a tractor that will have a net
cost of $36,000, will increase pre-tax operating cash flows before taking account of de-
preciation ... branch of the decision tree is equivalent to a time line. Thus,
the top line, which describes the payoffs under good conditions, has a cash flow
of Ϫ$5 million at t ϭ 0 and positive cash flows of $2.5 ... the standard deviation of the
NPV, and the coefficient of variation of the NPV?
ST-2
New project analysis
ST-1
Key terms
SELF-TEST PROBLEMS
573
Flexibility Options
It is often worth spending money...