Đang tải... (xem toàn văn)
Đây là hướng dẫn sử dụng phần mềm Mastercam-X4. hướng dẫn có các hình ảnh và ví dụ cụ thể
Mill Level 3 Training TutorialsTo order more books:Call 1 800 529 5517 orVisit www.inhousesolutions.com orContact your Mastercam Dealer Mastercam X4 Training Tutorials Mill Level 3 ApplicationsDate: June 15, 2009Copyright © 1984 2009 In House Solutions Inc. All rights reserved.Software: Mill Mastercam X4Author: Mariana LendelISBN: 978 1 926566 23 8NoticeIn House Solutions Inc. reserves the right to make improvements to this manual at any time andwithout notice.Disclaimer of All Warranties and LiabilityIn House Solutions Inc. makes no warranties, either express or implied, with respect to thismanual or with respect to the software described in this manual, its quality, performance,merchantability, or fitness for any particular purpose. In House Solutions Inc. manual is sold orlicensed "as is." The entire risk as to its quality and performance is with the buyer. Should themanual prove defective following its purchase, the buyer (and not In House Solutions Inc., itsdistributor, or its retailer) assumes the entire cost of all necessary servicing, repair, orcorrection, and any incidental or consequential damages. In no event will In House Solutions Inc.be liable for direct, indirect, or consequential damages resulting from any defect in the manual,even if In House Solutions Inc. has been advised of the possibility of such damages. Somejurisdictions do not allow the exclusion or limitation of implied warranties or liability forincidental or consequential damages, so the above limitation or exclusion may not apply to you.CopyrightsThis manual is protected under the copyright laws of Canada and the United States. All rights arereserved. This document may not, in whole or part, be copied, photocopied, reproduced,translated or reduced to any electronic medium or machine readable form without priorconsent, in writing, from In House Solutions Inc.TrademarksMastercam is a registered trademark of CNC Software, Inc.Microsoft, the Microsoft logo, MS, and MS DOS are registered trademarks of MicrosoftCorporation; Mastercam Verify is created in conjunction with Sirius Systems Corporation;Windows 95, Windows NT; and Windows XP are registered trademarks of MicrosoftCorporation.Acknowledgements"Thanks to the In House Solutions team for helping in the production and marketing of thisbook. It simply wouldn't be the same without all your efforts. Finally, thank you, the reader formaking this purchase; I hope it serves you well."Mariana Lendel TABLE OF CONTENTSGetting Started A1Graphic User Interface ANavigate Through the System . ASetting the Toolbar States . ASetting the Grid . A1246Surface ModelingTUTORIALSB111Tutorial #1, Revolved & Flat Boundary Surfaces, Pocket, Parallel & Contour Toolpaths 1 1Tutorial #2, Ruled and Flat Boundary Surfaces, Radial and Scallop Toolpaths . 2 1Tutorial #3, Net Surface, Pocket and Restmill & Finish Blend Toolpaths 3 1Tutorial #4, Swept & Flat Boundary Surfaces, Rough Flowline & Plunge, Finish Blend & PencilToolpaths . 4 1Tutorial #5, Revolved & Fillet Surfaces, HS Core Roughing & Finish Scallop, Pocket facing, Pencil &Project Toolpaths 5 1Tutorial #6, Revolved surface, HS Area Roughing, Finish Contour, Leftover and Project for MachiningRaised Letters 6 1Tutorial #7, Draft, Swept, Revolve and Fillet Surfaces and High Speed Toolpaths:Core Roughing, Horizontal Area, Waterline and Scallop Rest Passes 7 1Tutorial #8, Ruled, Swept, Revolve and Fillet Surfaces and High Speed Toolpaths:Core Roughing, Horizontal Area, Scallop, Scallop Rest Passes and Pencil . 8 1General Notes C1Default Key Assignments . CCustomizing . CKey Mapping CData Entry Shortcuts CSurface Toolpath Parameters . CCreate Geometry in 3D CSolids Menu . CSolids Manager CChaining . CWindow Selection CChaining and Window Options CToolpaths Manager . CProperties CMilling G Codes . C237910394445475051535861 TUTORIAL SERIES FORTUTORIAL 6REVOLVED SURFACE HIGH SPEED AREA ROUGHING, FINISH CONTOUR,FINISH LEFTOVER, AND FINISH PROJECT TOOLPATHS TO MACHINERAISED LETTERS Mill Level 3Objectives:The Student will design a 2 dimensional drawing by:Creating a rectangle.Creating parallel lines.Creating line endpoints.Creating arc tangent through a point.Creating fillets.Trimming the geometry.Moving the geometry.Creating the letters.Creating an obround shape.The Student will design a 3 dimensional drawing by:Creating the revolved surface.Creating a flat surface using rectangle command.Trim surface to curve.Creating the bounding box.Creating an offset surface.The Student will create a 3 dimensional milling toolpath consisting of:Roughing the cavity using surface high speed area mill toolpath.Finishing the cavity using surface finish contour toolpath.Finishing the fillets using surface finish leftover.Creating two 2D pockets toolpaths to be used in surface finish project.Using finish project toolpaths to machine the raised letters.The Student will check the toolpath using Mastercam’s Verify module by:Defining a 3 dimensional block, the size of the work piece.Running the verify function to machine the part on the screen.Page 6 2TUTORIAL 6 Mill Level 3 TUTORIAL 6GEOMETRY CREATIONTo start a new file from Mastercam:FileNewBefore starting the geometry creation we should customize the toolbars to see the toolbars requiredto create the geometry and machine a 3D part. See Getting started.Operation manager to the left of the screen can be hidden to gain more space in the graphic area fordesign. Press Alt + O to remove it.Before starting the geometry make sure that the Grid is enabled. It will show you where the partorigin is. See Getting started page A 6 for details.Page 6 3 Mill Level 3STEP 1: CREATE THE 2D PROFILE TO BE REVOLVEDNote that for the revolved surface we will only need half of the 2D wireframe.Step Preview:1.1 Create the 2.1" by 7.25" rectangleSub Step Preview:CreateRectangleTUTORIAL 6Enter the WidthEnter the Height2.1 (Tab).7.25 (Enter).Make sure that Anchor to center is not enabled.Page 6 4 123doc.vn