Đang tải... (xem toàn văn)
LINUX SOFTWARE RAID
LINUX SOFTWARE RAID Introduction The main goals of using redundant arrays of inexpensive disks (RAID) are to improve disk data performance and provide data redundancy RAID can be handled either by the operating system software or it may be implemented via a purpose built RAID disk controller card without having to configure the operating system at all This chapter will explain how to configure the software RAID schemes supported by RedHat/Fedora Linux For the sake of simplicity, the chapter focuses on using RAID for partitions that include neither the /boot or the root (/) filesystems RAID Types Whether hardware- or software-based, RAID can be configured using a variety of standards Take a look at the most popular Linear Mode RAID In the Linear RAID, the RAID controller views the RAID set as a chain of disks Data is written to the next device in the chain only after the previous one is filled The aim of Linear RAID is to accommodate large filesystems spread over multiple devices with no data redundancy A drive failure will corrupt your data Linear mode RAID is not supported by Fedora Linux RAID With RAID 0, the RAID controller tries to evenly distribute data across all disks in the RAID set Envision a disk as if it were a plate, and think of the data as a cake You have four cakes- chocolate, vanilla, cherry and strawberry-and four plates The initialization process of RAID 0, divides the cakes and distributes the slices across all the plates The RAID drivers make the operating system feel that the cakes are intact and placed on one large plate For example, four 9GB hard disks configured in a RAID set are seen by the operating system to be one 36GB disk Like Linear RAID, RAID aims to accommodate large filesystems spread over multiple devices with no data redundancy The advantage of RAID is data access speed A file that is spread over four disks can be read four times as fast You should also be aware that RAID is often called striping RAID can accommodate disks of unequal sizes When RAID runs out of striping space on the smallest device, it then continues the striping using the available space on the remaining drives When this occurs, the data access speed is lower for this portion of data, because the total number of RAID drives available is reduced For this reason, RAID is best used with drives of equal size RAID is supported by Fedora Linux Figure 26.1 illustrates the data allocation process in RAID RAID With RAID 1, data is cloned on a duplicate disk This RAID method is therefore frequently called disk mirroring Think of telling two people the same story so that if one forgets some of the details you can ask the other one to remind you When one of the disks in the RAID set fails, the other one continues to function When the failed disk is replaced, the data is automatically cloned to the new disk from the surviving disk RAID also offers the possibility of using a hot standby spare disk that will be automatically cloned in the event of a disk failure on any of the primary RAID devices RAID offers data redundancy, without the speed advantages of RAID A disadvantage of software-based RAID is that the server has to send data twice to be written to each of the mirror disks This can saturate data busses and CPU use With a hardware-based solution, the server CPU sends the data to the RAID disk controller once, and the disk controller then duplicates the data to the mirror disks This makes RAID-capable disk controllers the preferred solution when implementing RAID A limitation of RAID is that the total RAID size in gigabytes is equal to that of the smallest disk in the RAID set Unlike RAID 0, the extra space on the larger device isn't used RAID is supported by Fedora Linux Figure 26.1 illustrates the data allocation process in RAID Figure 26-1 RAID And RAID Operation RAID RAID operates likes RAID but inserts a special error-correcting or parity chunk on an additional disk dedicated to this purpose RAID requires at least three disks in the RAID set and can survive the loss of a single drive only When this occurs, the data in it can be recreated on the fly with the aid of the information on the RAID set's parity disk When the failed disk is replaced, it is repopulated with the lost data with the help of the parity disk's information RAID combines the high speed provided of RAID with the redundancy of RAID Its major disadvantage is that the data is striped, but the parity information is not In other words, any data written to any section of the data portion of the RAID set must be followed by an update of the parity disk The parity disk can therefore act as a bottleneck For this reason, RAID isn't used very frequently RAID is not supported by Fedora Linux RAID RAID improves on RAID by striping the parity data between all the disks in the RAID set This avoids the parity disk bottleneck, while maintaining many of the speed features of RAID and the redundancy of RAID Like RAID 4, RAID can survive the loss of a single disk only RAID is supported by Fedora Linux Figure 26.2 illustrates the data allocation process in RAID Linux RAID requires a minimum of three disks or partitions Figure 26-2 RAID Operation Before You Start Specially built hardware-based RAID disk controllers are available for both IDE and SCSI drives They usually have their own BIOS, so you can configure them right after your system's the power on self test (POST) Hardware-based RAID is transparent to your operating system; the hardware does all the work If hardware RAID isn't available, then you should be aware of these basic guidelines to follow when setting up software RAID IDE Drives To save costs, many small business systems will probably use IDE disks, but they have some limitations The total length of an IDE cable can be only a few feet long, which generally limits IDE drives to small home systems IDE drives not hot swap You cannot replace them while your system is running Only two devices can be attached per controller The performance of the IDE bus can be degraded by the presence of a second device on the cable The failure of one drive on an IDE bus often causes the malfunctioning of the second device This can be fatal if you have two IDE drives of the same RAID set attached to the same cable For these reasons, I recommend you use only one IDE drive per controller when using RAID, especially in a corporate environment In a home or SOHO setting, IDE-based software RAID may be adequate Serial ATA Drives Serial ATA type drives are rapidly replacing IDE, or Ultra ATA, drives as the preferred entry level disk storage option because of a number of advantages: The drive data cable can be as long as meter in length versus IDE's 18 inches Serial ATA has better error checking than IDE There is only one drive per cable which makes hot swapping, or the capability to replace components while the system is still running, possible without the fear of affecting other devices on the data cable There are no jumpers to set on Serial ATA drives to make it a master or slave which makes them simpler to configure IDE drives have a 133Mbytes/s data rate whereas the Serial ATA specification starts at 150 Mbytes/sec with a goal of reaching 600 Mbytes/ s over the expected ten year life of the specification If you can't afford more expensive and faster SCSI drives, Serial ATA would be the preferred device for software and hardware RAID SCSI Drives SCSI hard disks have a number of features that make them more attractive for RAID use than either IDE or Serial ATA drives SCSI controllers are more tolerant of disk failures The failure of a single drive is less likely to disrupt the remaining drives on the bus SCSI cables can be up to 25 meters long, making them suitable for data center applications Much more than two devices may be connected to a SCSI cable bus It can accommodate (single-ended SCSI) or 15 (all other SCSI types) devices Some models of SCSI devices support "hot swapping" which allows you to replace them while the system is running SCSI currently supports data rates of up to 640 Mbytes/s making them highly desirable for installations where rapid data access is imperative SCSI drives tend to be more expensive than IDE drives, however, which may make them less attractive for home use Should I Use Software RAID Partitions Or Entire Disks? It is generally a not a good idea to share RAID-configured partitions with nonRAID partitions The reason for this is obvious: A disk failure could still incapacitate a system If you decide to use RAID, all the partitions on each RAID disk should be part of a RAID set Many people simplify this problem by filling each disk of a RAID set with only one partition Backup Your System First Software RAID creates the equivalent of a single RAID virtual disk drive made up of all the underlying regular partitions used to create it You have to format this new RAID device before your Linux system can store files on it Formatting, however, causes all the old data on the underlying RAID partitions to be lost It is best to backup the data on these and any other partitions on the disk drive on which you want implement RAID A mistake could unintentionally corrupt valid data Configure RAID In Single User Mode As you will be modifying the disk structure of your system, you should also consider configuring RAID while your system is running in single-user mode from the VGA console This makes sure that most applications and networking are shutdown and that no other users can access the system, reducing the risk of data corruption during the exercise [root@bigboy tmp]# init Once finished, issue the exit command, and your system will boot in the default runlevel provided in the /etc/inittab file Configuring Software RAID Configuring RAID using Fedora Linux requires a number of steps that need to be followed carefully In the tutorial example, you'll be configuring RAID using a system with three pre-partitioned hard disks The partitions to be used are: /dev/hde1 /dev/hdf2 /dev/hdg1 Be sure to adapt the various stages outlined below to your particular environment RAID Partitioning You first need to identify two or more partitions, each on a separate disk If you are doing RAID or RAID 5, the partitions should be of approximately the same size, as in this scenario RAID limits the extent of data access on each partition to an area no larger than that of the smallest partition in the RAID set Determining Available Partitions First use the fdisk -l command to view all the mounted and unmounted filesystems available on your system You may then also want to use the df -k command, which shows only mounted filesystems but has the big advantage of giving you the mount points too These two commands should help you to easily identify the partitions you want to use Here is some sample output of these commands [root@bigboy tmp]# fdisk -l Disk /dev/hda: 12.0 GB, 12072517632 bytes 255 heads, 63 sectors/track, 1467 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start /dev/hda1 * /dev/hda2 14 /dev/hda3 145 /dev/hda4 210 /dev/hda5 210 /dev/hda15 1455 [root@bigboy tmp]# End 13 144 209 1467 655 Blocks 104391 1052257+ 522112+ 10104885 3582463+ 1467 [root@bigboy tmp]# df -k Filesystem 1K-blocks on /dev/hda2 1035692 /dev/hda1 101086 /dev/hda15 101086 /dev/hda7 5336664 [root@bigboy tmp]# 104391 Id 83 83 82 83 System Linux Linux Linux swap Extended Linux 83 Linux Used Available Use% Mounted 163916 8357 4127 819164 87510 91740 464228 4601344 17% / 9% /boot 5% /data1 10% /var Unmount the Partitions You don't want anyone else accessing these partitions while you are creating the RAID set, so you need to make sure they are unmounted [root@bigboy tmp]# umount /dev/hde1 [root@bigboy tmp]# umount /dev/hdf2 [root@bigboy tmp]# umount /dev/hdg1 Prepare The Partitions With FDISK You have to change each partition in the RAID set to be of type FD (Linux raid autodetect), and you can this with fdisk Here is an example using /dev/hde1 [root@bigboy tmp]# fdisk /dev/hde The number of cylinders for this disk is set to 8355 There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) Command (m for help): Use FDISK Help Now use the fdisk m command to get some help: Command (m for help): m p print the partition table q quit without saving changes s create a new empty Sun disklabel t change a partition's system id Command (m for help): Set The ID Type Partition /dev/hde1 is the first partition on disk /dev/hde Modify its type using the t command, and specify the partition number and type code You also should use the L command to get a full listing of ID types in case you forget In this case, RAID uses type fd, it may be different for your version of Linux Command (m for help): t Partition number (1-5): Hex code (type L to list codes): L 16 Hidden FAT16 17 Hidden HPFS/NTF 18 AST SmartSleep 1b Hidden Win95 FA Hex code (type L to Changed system type 61 SpeedStor f2 DOS secondary 63 GNU HURD or Sys fd Linux raid auto 64 Novell Netware fe LANstep 65 Novell Netware ff BBT list codes): fd of partition to fd (Linux raid autodetect) Command (m for help): Make Sure The Change Occurred Use the p command to get the new proposed partition table: Command (m for help): p Disk /dev/hde: 4311 MB, 4311982080 bytes 16 heads, 63 sectors/track, 8355 cylinders Units = cylinders of 1008 * 512 = 516096 bytes Device Boot /dev/hde1 autodetect /dev/hde2 /dev/hde4 /dev/hde5 /dev/hde6 Start End 4088 Blocks 2060320+ Id fd System Linux raid 4089 6608 6608 7501 5713 8355 7500 8355 819000 880992 450040+ 430888+ 83 83 83 Linux Extended Linux Linux Command (m for help): Save The Changes Use the w command to permanently save the changes to disk /dev/hde: Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table WARNING: Re-reading the partition table failed with error 16: Device or resource busy The kernel still uses the old table The new table will be used at the next reboot Syncing disks [root@bigboy tmp]# The error above will occur if any of the other partitions on the disk is mounted Repeat For The Other Partitions For the sake of brevity, I won't show the process for the other partitions It's enough to know that the steps for changing the IDs for /dev/hdf2 and /dev/hdg1 are very similar Preparing the RAID Set Now that the partitions have been prepared, we have to merge them into a new RAID partition that we'll then have to format and mount Here's how it's done Create the RAID Set You use the mdadm command with the create option to create the RAID set In this example we use the level option to specify RAID 5, and the raiddevices option to define the number of partitions to use [root@bigboy tmp]# mdadm create verbose /dev/md0 level=5 \ raid-devices=3 /dev/hde1 /dev/hdf2 /dev/hdg1 mdadm: layout defaults to left-symmetric mdadm: chunk size defaults to 64K mdadm: /dev/hde1 appears to contain an ext2fs file system size=48160K mtime=Sat Jan 27 23:11:39 2007 mdadm: /dev/hdf2 appears to contain an ext2fs file system size=48160K mtime=Sat Jan 27 23:11:39 2007 mdadm: /dev/hdg1 appears to contain an ext2fs file system size=48160K mtime=Sat Jan 27 23:11:39 2007 mdadm: size set to 48064K Continue creating array? y mdadm: array /dev/md0 started [root@bigboy tmp]# Confirm RAID Is Correctly Inititalized The /proc/mdstat file provides the current status of all RAID devices Confirm that the initialization is finished by inspecting the file and making sure that there are no initialization related messages If there are, then wait until there are none [root@bigboy tmp]# cat /proc/mdstat Personalities : [raid5] read_ahead 1024 sectors md0 : active raid5 hdg1[2] hde1[1] hdf2[0] 4120448 blocks level 5, 32k chunk, algorithm [3/3] [UUU] unused devices: [root@bigboy tmp]# Notice that the new RAID device is called /dev/md0 This information will be required for the next step Format The New RAID Set Your new RAID partition now has to be formatted The mkfs.ext3 command is used to this [root@bigboy tmp]# mkfs.ext3 /dev/md0 mke2fs 1.39 (29-May-2006) Filesystem label= OS type: Linux Block size=1024 (log=0) Fragment size=1024 (log=0) 36144 inodes, 144192 blocks 7209 blocks (5.00%) reserved for the super user First data block=1 Maximum filesystem blocks=67371008 18 block groups 8192 blocks per group, 8192 fragments per group 2008 inodes per group Superblock backups stored on blocks: 8193, 24577, 40961, 57345, 73729 Writing inode tables: done Creating journal (4096 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 33 mounts or 180 days, whichever comes first Use tune2fs -c or -i to override [root@bigboy tmp]# Create the mdadm.conf Configuration File Your system doesn't automatically remember all the component partitions of your RAID set This information has to be kept in the mdadm.conf file The formatting can be tricky, but fortunately the output of the mdadm detail -scan verbose command provides you with it Here we see the output sent to the screen [root@bigboy tmp]# mdadm detail scan verbose ARRAY /dev/md0 level=raid5 num-devices=4 UUID=77b695c4:32e5dd46:63dd7d16:17696e09 devices=/dev/hde1,/dev/hdf2,/dev/hdg1 [root@bigboy tmp]# Here we export the screen output to create the configuration file [root@bigboy tmp]# mdadm detail scan verbose > /etc/mdadm.conf Create A Mount Point For The RAID Set The next step is to create a mount point for /dev/md0 In this case we'll create one called /mnt/raid [root@bigboy mnt]# mkdir /mnt/raid Edit The /etc/fstab File The /etc/fstab file lists all the partitions that need to mount when the system boots Add an Entry for the RAID set, the /dev/md0 device /dev/md0 /mnt/raid ext3 defaults Do not use labels in the /etc/fstab file for RAID devices; just use the real device name, such as /dev/md0 In older Linux versions, the /etc/rc.d/rc.sysinit script would check the /etc/fstab file for device entries that matched RAID set names listed in the now unused /etc/raidtab configuration file The script would not automatically start the RAID set driver for the RAID set if it didn't find a match Device mounting would then occur later on in the boot process Mounting a RAID device that doesn't have a loaded driver can corrupt your data and produce this error Starting up RAID devices: md0(skipped) Checking filesystems /raiddata: Superblock has a bad ext3 journal(inode8) CLEARED ***journal has been deleted - file system is now ext only*** /raiddata: The filesystem size (according to the superblock) is 2688072 blocks The physical size of the device is 8960245 blocks Either the superblock or the partition table is likely to be corrupt! /boot: clean, 41/26104 files, 12755/104391 blocks /raiddata: UNEXPECTED INCONSISTENCY; Run fsck manually (ie without -a or -p options) If you are not familiar with the /etc/fstab file use the man fstab command to get a comprehensive explanation of each data column it contains The /dev/hde1, /dev/hdf2, and /dev/hdg1 partitions were replaced by the combined /dev/md0 partition You therefore don't want the old partitions to be mounted again Make sure that all references to them in this file are commented with a # at the beginning of the line or deleted entirely #/dev/hde1 #/dev/hdf2 #/dev/hdg1 /data1 /data2 /data3 ext3 ext3 ext3 defaults defaults defaults 2 Mount The New RAID Set Use the mount command to mount the RAID set You have your choice of methods: The mount command's -a flag causes Linux to mount all the devices in the /etc/fstab file that have automounting enabled (default) and that are also not already mounted [root@bigboy tmp]# mount -a You can also mount the device manually [root@bigboy tmp]# mount /dev/md0 /mnt/raid Check The Status Of The New RAID The /proc/mdstat file provides the current status of all the devices [root@bigboy tmp]# raidstart /dev/md0 [root@bigboy tmp]# cat /proc/mdstat Personalities : [raid5] read_ahead 1024 sectors md0 : active raid5 hdg1[2] hde1[1] hdf2[0] 4120448 blocks level 5, 32k chunk, algorithm [3/3] [UUU] unused devices: [root@bigboy tmp]# Conclusion Linux software RAID provides redundancy across partitions and hard disks, but it tends to be slower and less reliable than RAID provided by a hardwarebased RAID disk controller Hardware RAID configuration is usually done via the system BIOS when the server boots up, and once configured, it is absolutely transparent to Linux Unlike software RAID, hardware RAID requires entire disks to be dedicated to the purpose and when combined with the fact that it usually requires faster SCSI hard disks and an additional controller card, it tends to be expensive Remember to take these factors into consideration when determining the right solution for your needs and research the topic thoroughly before proceeding Weighing cost versus reliability is always a difficult choice in systems administration ... of RAID and the redundancy of RAID Like RAID 4, RAID can survive the loss of a single disk only RAID is supported by Fedora Linux Figure 26.2 illustrates the data allocation process in RAID Linux. .. bottleneck For this reason, RAID isn''t used very frequently RAID is not supported by Fedora Linux RAID RAID improves on RAID by striping the parity data between all the disks in the RAID set This avoids... used RAID is supported by Fedora Linux Figure 26.1 illustrates the data allocation process in RAID Figure 26-1 RAID And RAID Operation RAID RAID operates likes RAID but inserts a special error-correcting