Structural details in concrete, 1st ed (1992) M. Y. H. Bangash

Structural detailing in concrete

Structural detailing in concrete

... 1/8 in 1/8 in or proportion 1/8 in. , 3/16 in. , 3/4 in 1/8 in. , 1/4 in 1/2 in. , 3/4 in. , in 12 in. , in 1/2 in. , 3/4 in. , in 12 in. , in 1/8 in. , 3/16 in. , 1/4 in 3/4 in. , in. , 12 in. , in 1/2 in. , ... REQUIREMENTS FOR STRUCTURAL DETAILING IN CONCRETE LAYOUT OF AN EXISTING BUILDING (BASED ON ACI/PCI/ASCE CODES) SHEET NO I.7 13 STRUCTURAL...
Ngày tải lên : 20/08/2015, 10:02
  • 469
  • 314
  • 1
Báo cáo khoa học: High levels of structural disorder in scaffold proteins as exemplified by a novel neuronal protein, CASK-interactive protein1 pot

Báo cáo khoa học: High levels of structural disorder in scaffold proteins as exemplified by a novel neuronal protein, CASK-interactive protein1 pot

... C-terminal Caskin1 are functional and may interact with SH3 domain-containing proteins, such as Abi2 [We have also found an in vivo association and colocalization of Abi2 with Caskin1 (A Balazs, ... of Caskin1 fragments As described in the introductory paragraphs, the N-terminal half of Caskin1 contains a number of well-known domains involved in protein–protein interacti...
Ngày tải lên : 16/03/2014, 02:20
  • 13
  • 408
  • 0
The MEMS Handbook (1st Ed) - M. Gad el Hak Part 1 ppsx

The MEMS Handbook (1st Ed) - M. Gad el Hak Part 1 ppsx

... 2002 by CRC Press LLC 10 2 10 4 10 -1 6 1 0 -1 4 10 6 10 8 10 10 10 12 10 14 10 16 10 18 10 20 1 0 -1 2 1 0 -1 0 1 0-8 1 0-6 1 0-4 1 0-2 10 0 10 2 Diameter of Proton Typical Man-Made Devices FIGURE 1. 1 10 Scale of things, ... be set The manufacturer of a MEMS device needs to understand the relation between the processing and the properties...
Ngày tải lên : 10/08/2014, 02:21
  • 6
  • 346
  • 0
The MEMS Handbook (1st Ed) - M. Gad el Hak Part 2 ppt

The MEMS Handbook (1st Ed) - M. Gad el Hak Part 2 ppt

... cross-flow heat exchanger constructed from a stack of 50 14-mm × 14-mm foils, each containing 34 20 0- m-wide × 10 0- m-deep channels machined into the 20 0- m-thick stainless steel foils by the process ... microcutters These methods and the characteristics of the resulting flow channels are discussed elsewhere in this handbook Microchannels offer advantages due to their high...
Ngày tải lên : 10/08/2014, 02:21
  • 4
  • 322
  • 0
The MEMS Handbook (1st Ed) - M. Gad el Hak Part 3 pptx

The MEMS Handbook (1st Ed) - M. Gad el Hak Part 3 pptx

... and power generation within the same microchip The small size, light weight and high-durability of MEMS, combined with the mass-fabrication ability, result in low-cost systems with a wide variety ... technologies, the need for greater sophistication in microelectromechanical systems (MEMS) design will increase Fluid film lubrication has been a critical issue from the outset of MEMS...
Ngày tải lên : 10/08/2014, 02:21
  • 5
  • 248
  • 0
The MEMS Handbook (1st Ed) - M. Gad el Hak Part 4 pdf

The MEMS Handbook (1st Ed) - M. Gad el Hak Part 4 pdf

... of MEMS technology are controls-related because of the utility of MEMS devices in sensor and actuator technologies Because the area of control is far too vast to be entirely presented in one self-contained ... microchannels becomes a reality, however, several fundamental problems that arise from the small dimension of the channels must be solved Most of these problems originate fr...
Ngày tải lên : 10/08/2014, 02:21
  • 5
  • 437
  • 0

Xem thêm

Từ khóa: