... all at once. Chapter 21 discusses how to draw 3D lines and polylines.
Cross-
Reference
Note
13_788864 ch06.qxp 5 /22 /06 7 :24 PM Page 114
1 02
Part I ✦ AutoCAD and AutoCAD LT Basics
7. Choose View➪ ... sizes.
Table 5-3 : Standard Paper Sheet Sizes in the United States (in inches)
Size Width Height Size Width Height
A118
1
2 D3 422
B1711 E4434
C 221 7
Table 5-4 lists standa...
... register (SAR) and Sigma-Delta topologies.
SAR Converter Layout
SAR A/D converters can be found with 8-bit, 10-bit, 1 2- bit, 1 6-
bit and sometimes 18-bit resolution. Originally, the process and
architecture ... signal at the output of the load-cell sensor is gained by a two-op amp instrumentation amplifier, filtered and digitized with a
1 2- bit A/D Converter, MCP 320 1. The r...
... how to set
up and change a document, how to open and save files, and how to export
and place files. You also find out the difference between pixel-based docu-
ments and vector-based documents. ... handle
Straight line segment
FIGURE 4.4
Anchor points, control handles, and control handle lines along a path
Control handle lines
Anchor point
Control handle
08_584750-ch04.indd 7308_...
... whether this book is for you.
If you are a new AutoCAD or AutoCAD LT user
If you are new to AutoCAD or AutoCAD LT, the AutoCAD 20 07 and AutoCAD LT 20 07 Bible
guides you through all that you need ... LT
®
20 07 Bible
01_788864 ffirs.qxp 5 /22 /06 7:10 PM Page i
Preface
W
elcome to the AutoCAD 20 07 and AutoCAD LT 20 07 Bible. Whether you use...
... 5 /22 /06 7 :23 PM Page 24 3
22 0
Part II ✦ Drawing in Two Dimensions
STEPS: Lengthening and Shortening Objects
1. Open ab10-f.dwg from the CD-ROM.
2. Save the file as
ab1 0-0 7.dwg in your AutoCAD Bible ... layer.
On the
CD-ROM
18_788864 ch11.qxp 5 /22 /06 7 :22 PM Page 26 6
24 2
Part II ✦ Drawing in Two Dimensions
Customizing grips
You can turn grips on and off and customi...
... objects. You need to
use this command when you open drawings created in releases prior to 20 02 in AutoCAD
20 07 or AutoCAD LT 20 07. You might also need to use this command when dimensions become
disassociated ... that is,
AutoCAD and AutoCAD LT do not calculate dimension text. Figure 1 4 -2 3 shows two leaders.
Figure 1 4 -2 3: Using leaders to point to objects and...
... space, ab17-a
.dwg and ab-17-a-blk.dwg, are in the Drawings folder on the CD-ROM.
STEPS: Laying Out a Drawing in Paper Space
1. Open ab17-a.dwg from your CD-ROM.
2. Save the file as
ab1 7-0 2. dwg in ... You cannot create non-rect-
angular viewports in AutoCAD LT.
Tip
24 _788864 ch17.qxp 5 /22 /06 7 :20 PM Page 498
507
Chapter 17 ✦ Plotting and Printing Your Drawing
3. Set the p...
...
AutoCAD
Bible\ databases\ab20-prt.xls worksheet. Click OK three times and close the
Control Panel.
7. Open AutoCAD. Open
ab20-a.dwg from the CD-ROM. Save it as ab2 0-0 1.dwg in your
AutoCAD Bible ... Template.
2. If you haven’t already opened a data table, AutoCAD opens the Select Data Object dia-
log box. Choose a table and click Continue.
28 _788864 ch20.qxp 5 /22 /06 7:...
... Figure 2 3-3 0.
Figure 2 3-3 0: The completed table.
1
32_ 788864 ch23.qxp 5 /22 /06 7 :29 PM Page 754
773
Chapter 24 ✦ Creating Solids and Editing in 3D
The PYRAMID command is new for AutoCAD 20 07. Although ... Figure 2 3-1 8. The prompts are very similar to
those for a sphere.
Figure 2 3-1 8: A dome.
32_ 788864 ch23.qxp 5 /22 /06 7 :29 PM Page 7 42
756
Part IV ✦ D...
... drawings and files used in the following exercise on creating and configuring a sheet set,
ab26-f-1.dwg, ab26-f -2 . dwg, ab26-f-3.dwg, and ab26-f.dwt, are in the Drawings
folder on the CD-ROM.
STEPS: ... Set folder and again choose File ➪ New ➪ Folder. Name the new
folder
Model View Drawings.
3. Copy
ab26-f-1.dwg, ab26-f -2 . dwg, ab26-f-3.dwg, and ab26-f.dwt (a template file)
fr...