... situations.
Recommended codeofpracticefor the care and
Recommended codeofpracticefor the care and
handling of poultry from hatchery to processing plant
handling of poultry from hatchery ... Facilities forand handling of loose-housed poultry
5.2.1 Proper building design and accessibility to transport vehicles greatly improves the humane
handling of loose-housed poultry. Owners and operators ... feeding and watering space, an adequate and predictable supply of feed and
water, and an adequate number of nest boxes and roosts.
14
2.5 Supervision and protection of chickens
2.5.1 Chicken flocks...
... use of steelwork in building — Part 4: Codeofpracticefor design of composite slabs
with profiled steel sheeting.
BS 5950-5, Structural use of steelwork in building — Part 5: Codeofpractice ... carbon steel bars for the reinforcement of concrete.
BS 4482, Specification for cold reduced steel wire for the reinforcement of concrete.
BS 4483, Steel fabric for the reinforcement of concrete.
BS ... 5: Codeofpracticefor design of cold formed thin
gauge sections.
BS 5950-6, Structural use of steelwork in building — Part 6: Codeofpracticefor design of light gauge
profiled steel sheeting.
BS...
...
INTERNATIONAL
STANDARD
ISO/IEC
17799
Second edition
2005-06-15
Information technology — Security
techniques — Codeofpracticefor
information security management
Technologies de l'information ... Information
Labeling and secure handling of classified information is a key requirement for information sharing
arrangements. Physical labels are a common form of labeling. However, some information assets, ... guidelines
This codeofpractice may be regarded as a starting point for developing organization specific
guidelines. Not all of the controls and guidance in this codeofpractice may be applicable....
... conditions and system configurations, can be referenced to codes, guidelines
and practices of international standards (such as ASHRAE, CIBSE) or established local
standards or trade good practices, for ... or forced fan ventilation.
‘Director’ means the Director of Electrical and Mechanical Services.
Code ofPracticefor Building Energy Audit
EAC_2012 9 of 11 EMSD
cost benefit analyses, and ... date of issue of Energy Audit Form,
- name and address of building (English and Chinese),
- name and Registration No. of Registered Energy Assessor who has carried out
the energy audit, and...
... Chemical handling;
· Manual handling; and
· Vehicle and equipment safety.
ENVIRONMENTAL CODEOFPRACTICEFOR POULTRY FARMS IN WESTERN AUSTRALIA
33
PART 4 OTHER CONSIDERATIONS
ENVIRONMENTAL CODEOFPRACTICE ... Welfare of Animals: Land Transport of Poultry, available from the Internet site
<www.publish.csiro.au> ;and the Department of Local Government and Regional Development’s
Code ofPracticefor ... trucks for transportation to the central grading floor in Palmyra for grading and retail
distribution.
ENVIRONMENTAL CODEOFPRACTICEFOR POULTRY FARMS IN WESTERN AUSTRALIA
iv
ENVIRONMENTAL CODE OF...
... information is a shorthand way of determining how this
information is to be handled and protected.
7.2.2 Information labeling and handling
Control
An appropriate set of procedures for information ...
INTERNATIONAL
STANDARD
ISO/IEC
17799
Second edition
2005-06-15
Information technology — Security
techniques — Codeofpracticefor
information security management
Technologies de l'information ... techniques — Codeof
practice for information security management
1 Scope
This International Standard establishes guidelines and general principles for initiating, implementing,
maintaining, and...
... materials and workmanship: cold
formed sections and sheeting.
BS 6399-1, Loading for buildings Ð Codeof practice
for dead and imposed loads.
BS 6399-2, Loading for buildings Ð Codeof practice
for ... practicefor protective coating of iron
and steel structures against corrosion
1)
.
BS 5502-22, Buildings and structures for
agriculture Ð Codeofpracticefor design,
construction and loading.
BS ... properties of fasteners Ð
Bolts, screws and studs.
CP3 Codeof basic data for the design of buildings:
Chapter V: Part 2: Wind loads.
1.4 Terms and definitions
For the purposes of this part of BS...
... 3.4 and 3.5 of BS 8110-1:1985 or Tables 5.1 and 5.2 of BS 8110-2:1985.
Figure 4 — Typical profiles
BRITISH STANDARD
BS 5950-4:
1994
Structural use of
steelwork in building —
Part 4: Codeofpractice ... load
D
p
Overall depth of profiled steel sheets
D
s
Overall depth of composite slab
d
s
Effective depth of slab to centroid of
profiled steel sheets
E Modulus of elasticity of profiled steel sheets
F
a
End ... recommendations for
thedesign of composite slabs with profiled steel
sheeting. It covers slabs spanning only in the
direction of span of the profiled steel sheets.
This code applies to the design of composite...
... of first stiffener
h
sb
Vertical depth ofsecond stiffener
I
eff
Effective second moment of area of a section
I
min
Minimum required second moment of area of an effective edge stiffener
I
r
Second ... R
t,0.5
and R
m
should normally be taken as specified in the relevant product standard for the steel sheet or strip and used for
the formed sections. For information, the resulting values of Y
s
and ... Properties of materials and section properties
3.1 Range of thicknesses
The provisions of this Part of BS 5950 apply primarily to profiled steel sheet with a net thickness of steel base
metal of not...
... 3.1: Codeofpracticefor design of simple and continuous composite
beams;
— Section 3.2
1)
: Codeofpracticefor design of composite columns and frames;
— Part 4: Codeofpracticefor design of ... Specification for materials and workmanship: cold formed sections;
— Part 8: Codeofpracticefor fire resistant design;
— Part 9
1)
: Codeofpracticefor stressed skin design.
This Part of BS5950 ... the second moment of area of concrete core in the plane
of buckling;
I
r
is the second moment of area of the reinforcement in the
plane of buckling;
E
r
is the modulus of elasticity of reinforcement;
f
y
...
... 3.1 Codeofpracticefor
design of simple and continuous composite beams;
— Part 4: Codeofpracticefor design of composite slabs with profiled steel
sheeting;
— Part 5: Codeofpracticefor ... design of cold formed sections;
— Part 6
1)
: Codeofpracticefor design of light gauge profiled sheeting;
— Part 7: Specification for materials and workmanship: cold formed sections;
— Part 8: Code ... sections;
— Part 8: Codeofpracticefor fire resistant design;
— Part 9: Codeofpracticefor stressed skin design.
This Part of BS 5950 gives recommendations for the use of profiled steel sheeting...