Tài liệu Titanium and ITS Alloys docx

18 394 1
Tài liệu Titanium and ITS Alloys docx

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

Thông tin tài liệu

CHAPTER TITANIUM AND ITS ALLOYS Donald Knittel James B C Wu Cabot Corporation Kokomo, Indiana 6.1 INTRODUCTION 6.2 ALLOYS 6.2.1 Aerospace Alloys 6.2.2 Nonaerospace Alloys 6.2.3 Other Alloys 92 94 95 96 6.3 PHYSICALPROPERTIES CORROSION RESISTANCE 97 6.5 FABRICATION 6.5.1 Boiler Code 98 98 Drawing Bending Cutting and Grinding Welding 100 104 104 104 96 6.4 6.5.2 6.5.3 6.5.4 6.5.5 91 6.6 SPECIFICATIONS, STANDARDS, AND QUALITY CONTROL 105 6.7 HEALTH AND SAFETY FACTORS 107 USES 107 6.8 6.1 INTRODUCTION Titanium was first identified as a constituent of the earth's crust in the late 170Os In 1790, William Gregor, an English clergyman and mineralogist, discovered a black magnetic sand (ilmenite), which he called menaccanite after his local parish In 1795, a German chemist found that a Hungarian mineral, rutile, was the oxide of a new element he called titan, after the mythical Titans of ancient Greece In the early 190Os, a sulfate purification process was developed to commercially obtain highpurity TiO2 for the pigment industry, and titanium pigment became available in both the United States and Europe During this period, titanium was also used as an alloying element in irons and steels In 1910, 99.5% pure titanium metal was produced at General Electric from titanium tetrachloride and sodium in an evacuated steel container Since the metal did not have the desired properties, further work was discouraged However, this reaction formed the basis for the commercial sodium reduction process In the 1920s, ductile titanium was prepared with an iodide dissociation method combined with Hunter's sodium reduction process In the early 1930s, a magnesium vacuum reduction process was developed for reduction of titanium tetrachloride to metal Based on this process, the U.S Bureau of Mines (BOM) initiated a program in 1940 to develop commercial production Some years later, the BOM publicized its work on titanium and made samples available to the industrial community By 1948, the BOM produced batch sizes of 104 kg In the same year, E I du Pont de Nemours & Co., Inc., announced commercial availability of titanium, and the modern titanium metals industry began.1 By the mid-1950s, this new metals industry had become well established, with six producers, two other companies with tentative production plans, and more than 25 institutions engaged in research projects Titanium, termed the wonder metal, was billed as the successor to aluminum and stainless steels When, in the 1950s, the DOD (titanium's most staunch supporter) shifted emphasis from aircraft to missiles, the demand for titanium sharply declined Only two of the original titanium metal plants are still in use, the Titanium Metals Corporation of America's (TMCA) plant in Henderson, Reprinted with additions from Kirk-Othmer Encyclopedia of Chemical Technology, 3rd ed., Wiley, New York, 1983, Vol 23, by permission of the publisher Mechanical Engineers' Handbook, 2nd ed., Edited by Myer Kutz ISBN 0-471-13007-9 © 1998 John Wiley & Sons, Inc Nevada, and National Distillers & Chemical Corporation's two-stage sodium reduction plant built in the late 1950s at Ashtabula, Ohio, which now houses the sponge production facility for RMI Corporation (formerly Reactor Metals, Inc.) Overoptimism followed by disappointment has characterized the titanium-metals industry In the late 1960s, the future again appeared bright Supersonic transports and desalination plants were intended to use large amounts of titanium Oregon Metallurgical Corporation, a titanium melter, decided at that time to become a fully integrated producer (i.e., from raw material to mill products) However, the supersonic transports and the desalination industry did not grow as expected Nevertheless, in the late 1970s and early 1980s, the titanium-metal demand again exceeded capacity and both the United States and Japan expanded capacities This growth was stimulated by greater acceptance of titanium in the chemical-process industry, power-industry requirements for seawater cooling, and commercial and military aircraft demands However, with the economic recession of 1981-1983, the demand dropped well below capacity and the industry was again faced with hard times 6.2 ALLOYS Titanium alloy systems have been studied extensively A single company evaluated over 3000 compositions in years Alloy development has been aimed at elevated-temperature aerospace applications, strength for structural applications, and aqueous corosion resistance The principal effort has been in aerospace applications to replace nickel- and cobalt-base alloys in the 500-90O0C ranges To date, titanium alloys have replaced steel in the 200-50O0C range The useful strength and corrosionresistance temperature limit is ~550°C The addition of alloying elements alters the a-/3 transformation temperature Elements that raise the transformation temperature are called a stabilizers; elements that depress the transformation temperature are called /3 stabilizers; the latter are divided into /3-isomorphous and /3-eutectoid types The /3-isomorphous elements have limited a solubility, and increasing additions of these elements progressively depresses the transformation temperature The /3-eutectoid elements have restricted beta solubility and form intermetallic compounds by eutectoid decomposition of the /3 phase The binary phase diagram illustrating these three types of alloy systems is shown in Fig 6.1 The important a-stabilizing alloying elements include aluminum, tin, zirconium, and the interstitial alloying elements (i.e., elements that not occupy lattice positions) oxygen, nitrogen, and carbon Small quantities of interstitial alloying elements, generally considered to be impurities, have a very great effect on strength and ultimately embrittle the titanium at room temperature.3 The effects of oxygen, nitrogen and carbon on the ultimate tensile properties and elongation are shown in Table 6.1 These elements are always present and are difficult to control Nitrogen has the greatest effect, and commercial alloys specify its limit to be less than 0.05 wt % It may also be present as nitride (TiN) inclusions, which are detrimental to critical aerospace structural applications Oxygen additions increase strength and serve to identify several commercial grades This strengthening effect diminishes at elevated temperatures and under creep conditions at room temperature For cryogenic service, low oxygen content is specified ( 690 MPa (100,000 psi)] at a density of 4.507 g/cm3 Titanium alloys have a higher yield strength-to-density rating between -200 and 54O0C than either aluminum alloys or steel.6'16 Titanium alloys can be made with strength equivalent to high-strength steel, yet with density —60% that of iron alloys At ambient temperatures, titanium's strength-to-weight ratio is equal to that of magnesium, one and one-half times greater than that of aluminum, two times greater than that of stainless steel, and three times greater than that of nickel Alloys of titanium have much higher strength-to-weight ratios than alloys Table 6.5 Physical Properties of Titanium2 Property melting point, 0C boiling point, 0C density, g/cm a phase at 2O0C (3 phase at 8850C allotropic transformation, 0C latent heat of fusion, kJ/kg* latent heat of transition, kJ/kg a latent heat of vaporization, MJ/kg a entropy at 250C, J/mola thermal expansion coefficient at 2O0C per 0C thermal conductivity at 250C, W/(m-K) emissivity electrical resistivity at 2O0C, nll-m magnetic susceptibility, mks modulus of elasticity, GPa* tension compression shear Poisson's ratio lattice constants, nm a, 250C ft 90O0C vapor pressure, kPac specific heat, J/(kg-K) 298 K of nickel, aluminum, or magnesium, and stainless steel Because of its high melting point, titanium can be alloyed to maintain strength well above the useful limits of magnesium and aluminum alloys This property gives titanium a unique position in applications between 150 and 55O0C where the strength-to-weight ratio is the sole criterion Solid titanium exists in two allotropic crystalline forms The a phase, stable below 882.50C, is a hexagonal closed-packed structure, whereas the /3 phase, a bcc crystalline structure, is stable between 882.50C and the melting point of 16680C The high-temperature /3 phase can be found at room temperature when ^-stabilizing elements are present as impurities or additions (see Section 6.2) The a and /3 phases can be distinguished by examining an unetched polished mount with polarized light The OL is optically active and changes from light to dark as the microscope stage is rotated The microstructure of titanium is difficult to interpret without knowledge of the alloy content, working temperature, and thermal treatment.6'17'18 The heat-transfer qualities of titanium are characterized by the coefficient of thermal conductivity Even though this is low, heat transfer in service approaches that of admiralty brass (thermal conductivity seven times greater) because titanium's greater strength permits thinner-walled equipment, relative absence of corrosion scale, erosion-corrosion resistance permitting higher operating velocities, and inherently passive film 6.4 CORROSION RESISTANCE Titanium is immune to corrosion in all naturally occurring environments It does not corrode in air, even if polluted or moist with ocean spray It does not corrode in soil or even the deep salt-minetype environments where nuclear waste might be buried It does not corrode in any naturally occurring water and most industrial wastewater streams For these reasons, titanium has been termed the metal for the earth, and 20-30% of consumption is used in corrosion-resistance applications Even though titanium is an active metal, it resists decomposition because of a tenacious protective oxide film This film is insoluble, repairable, and nonporous in many chemical media and provides excellent corrosion resistance However, where this oxide film is broken, the corrosion rate is very rapid However, usually the presence of a small amount of water is sufficient to repair the damaged oxide film In a seawater solution, this film is maintained in the passive region from 0.2 to 10 V versus the saturated calomel electrode.19'20 Titanium is resistant to corrosion attack in oxidizing, neutral, and inhibited reducing conditions Examples of oxidizing environments are nitric acid, oxidizing chloride (FeCl3 and CuCl2) solutions, and wet chlorine gas Neutral conditions include all neutral waters (fresh, salt, and brackish), neutral salt solutions, and natural soil environments Examples of inhibited reducing conditions are in hydrochloric or sulfuric acids with oxidizing inhibitors and in organic acids inhibited with small amounts of water Corrosion resistances to a variety of media are given in Table 6.6.22 Titanium resistance to aqueous chloride solutions and chlorine account for most of its use in corrosion-resistant applications Titanium corrodes very rapidly in acid fluoride environments The degree of attack generally increases with the acidity and the fluoride content It is attacked in boiling HCl or H2SO4 at acid concentrations >1% or in —10 wt % acid concentration at room temperature Titanium is also attacked by hot caustic solutions, phosphoric acid solutions (concentrations above 25 wt %), boiling AlCl3 (concentrations >15 wt %), dry chlorine gas, anhydrous ammonia above 15O0C, and dry hydrogen-dihydrogen sulfide above 15O0C Titanium is susceptible to pitting and crevice corrosion in aqueous chloride environments The area of susceptibility is shown in Fig 6.2 as a function of temperature and sodium chloride content.22 The susceptibility also depends on pH The susceptibility temperature increases parabolically from 650C as pH is increased from zero With ASTM grades or 12, crevice-corrosion attack is not observed above pH until ~270°C Noble alloying elements shift the equlibrium potential into the passive region where a protective film is formed and maintained Titanium does not stress crack in environments that cause stress cracking of other metal alloys (i.e., boiling 42% MgCl2, NaOH, sulfides, etc.) Some of the alloys are susceptible to hot-salt stress cracking; however, this is a laboratory observation and has not been confirmed in service Titanium stress cracks in methanol containing acid chlorides or sulfates, red fuming nitric acid, nitrogen tetroxide, and trichloroethylene Titanium is susceptible to failure by hydrogen embrittlement Hydrogen attack initiates at sites of surface iron contamination or when titanium is galvanically coupled with iron.23 In hydrogencontaining environments, titanium absorbs hydrogen above 8O0C or in areas of high stress If the surface oxide is removed by vacuum annealing or abrasion, pure dry hydrogen reacts at lower temperatures Small amounts of oxygen or water vapor repair the oxide film and prevent this occurence Molybdenum-containing alloys are less susceptible to hydrogen attack Titanium resists this oxidation in air up to 65O0C Noticeable scale forms and embrittlement occurs at higher temperatures Surface contaminants accelerate oxidation In the presence of oxygen, the metal does not react significantly with nitrogen Spontaneous ignition occurs in gas mixtures containing more than 40% oxygen under impact loading or abrasion Ignition also occurs in dry halogen gases Titanium resists erosion-corrosion by fast-moving sand-laden water In a high-velocity sand-laden seawater test (8.2 m/sec) for a 60-day period, titanium performed more than 100 times better than 18 Cr-8 Ni stainless steel, Monel, or 70 Cu-30 Ni Resistance to cavitation (i.e., corrosion on surfaces exposed to high-velocity liquids) is better than by most other structural metals.21'22 In galvanic coupling, titanium is usually the cathode metal and, consequently, is not attacked The galvanic potential in flowing seawater in relation to other metals is shown in Table 6.7.21 Since titanium is the cathode metal, hydrogen attack may be of concern, as it occurs with titanium coupled to iron 6.5 FABRICATION Titanium can be fabricated similarly to nickel-base alloys and stainless steels However, the characteristics of titanium have to be taken into account Compared to these materials, titanium has: Lower modulus of elasticity Lower ductility Higher melting point Lower thermal conductivity Smaller strain-hardening coefficient, thereby, lower uniform elongation Greater tendency to cold weld, thereby, greater tendency to gall or seize Greater tendency to be contaminated by oxygen, nitrogen, hydrogen, and carbon 6.5.1 Boiler Code The allowable stress values as determined by the Boiler and Pressure Vessel Committee of the American Society of Mechanical Engineers are listed in Tables 6.8 and 6.9 for various titanium grades and product forms Table 6.6 Corrosion Data for ASTM Grade Titanium2'16'21 Media acetaldehyde acetic acid adipic acid aluminum chloride, aerated Temperature, 0C Cone, wt % 100 5-99.7 67 10 10 20 25 25 40 ammonia + 28% urea + 20.5% H2O 32.2 + 19% CO2 + 0.3% inerts + air ammonia carbamate 50 ammonium perchlorate aerated 20 aniline hydrochloride 20 aqua regia 3:1 3:1 barium chloride, aerated 5-20 bromine-water solution calcium chloride 10 20 55 60 62 73 calcium hypochlorite chlorine gas, wet >0.7 H2O >0.5 H2O chlorine gas, dry

Ngày đăng: 26/12/2013, 01:18

Từ khóa liên quan

Tài liệu cùng người dùng

  • Đang cập nhật ...

Tài liệu liên quan