23 Notes on the use of hand-held test devices for installation of the KRONE Cat.6 KM8 products Page 1 of 9 December 2001 Notes on the use of hand-held test devices for installation of the KRONE Cat.6 K K M M 8 8 p p r r o o d d u u c c t t s s § FLUKE DSP 4000 / 4100 / 4300 § MICROTEST OMNIScanner2™ § Agilent WireScope 350 § IDEAL LT8600LT 23 Notes on the use of hand-held test devices for installation of the KRONE Cat.6 KM8 products Page 2 of 9 December 2001 FLUKE DSP 4000 / 4100 / 4300 The FLUKE DSP 4X00 performs all tests required by ISO/IEC 11801; DIN EN 50173, for example: § Cabling errors § NEXT § Power Sum NEXT § Return Loss § ELFEXT § Power Sum ELFEXT § Characteristic Impedance § Attenuation § ACR § Power Sum ACR § DC resistance § Length § Delay Skew For further details please refer to the FLUKE documents. Before you start a large-scale series of measurements go to the FLUKE homepage to see whether there are current drivers, etc. for downloading: http://www.flukenetworks.com/de/default.htm The following releases are the most current ones DSP 4000: Software Release 3.8 DSP 4100: Software Release 4.8 CableManager Software: Software V 4.6 Accessories: § Permanent Link Interface Adapter DSP LIA101S: Includes: § 2 interface adapters § one set Personality module DSP-PM01 for KRONE KM8 (this is included in the standard delivery) § PM02 to PMxx are not relevant for measurement of the KRONE KM8 Note: § FLUKE DSP 4300 with new accessories (channel Cat.6 test head) is in preparation! 23 Notes on the use of hand-held test devices for installation of the KRONE Cat.6 KM8 products Page 3 of 9 December 2001 Cat 6/5e Channel Adapter DSP-LIA012S: § Contains two interface adapters for use with the DSP 4000 family Basic Link Adapter: § DSP-LIA041S KRONE basic link adapter set for KRONE HighBand § This adapter cannot be used with the KM8 Required Settings: § Cable type § Category 5e, 6 or 7 § UTP or STP § NVP´s (nominal velocity propagation) are in general already set as instrument default values; otherwise see the table below § Measurement of shield influence: Yes / No (generally the choice is "No") NVP settings for KRONE cables: Cable Order No. NVP * KRONE Cat 7 S-STP 7053 3 062-25 0.80 KRONE Cat 6 S-STP 7053 2 062-25 0.80 KRONE Cat 6 FTP 7053 2 021-04 0.68 KRONE Cat 6 UTP 7053 2 001-00 0.68 KRONE Cat 5e S-FTP 7053 1 052-25 0.66 KRONE Cat 5 FTP 7053 1 021-04 0.68 KRONE Cat 5 UTP 7053 1 001-00 0.68 KRONE C6 TrueNet UTP 7052 2 110-00 0.70 KRONE C5e TrueNet UTP 7052 1 110-00 0.70 * Note: The correct NVP setting is necessary; it has an influence on the determination of the cable length by the instrument. 23 Notes on the use of hand-held test devices for installation of the KRONE Cat.6 KM8 products Page 4 of 9 December 2001 MICROTEST OMNIScanner2™ The MICROTEST OMNIScanner2™ performs all tests required by ISO/IEC 11801, for example: § Cabling errors § NEXT § Power Sum NEXT § Return Loss § ELFEXT § Power Sum ELFEXT § Attenuation § ACR § Power Sum ACR § DC resistance § Length § Delay Skew For further details please refer to the MICROTEST documents Before you start a large-scale series of measurements go to the MICROTEST homepage to see whether there are current drivers, etc. for downloading: http://www.microtest.de The following releases are the most current ones: OMNIScanner2™: OMNIScanner 5.11 Scanlink PC Software: Software V 7.0 Accessories: § Permanent Link Interface Adapter 8262-38: Includes: § 2 interface adapters, suitable § for the KRONE KM8 23 Notes on the use of hand-held test devices for installation of the KRONE Cat.6 KM8 products Page 5 of 9 December 2001 Cat 6/5e Channel Adapter 8262-02: Basic Link Adapter: § 8262-22: KRONE Basic Link Adapter Set for the KRONE HighBand § This adapter is not recommended for the KM8 Required settings: § Type of cable § Category 5e, 6 or 7 § UTP or STP § NVP´s (nominal velocity propagation) are in general already set as instrument default values; otherwise see the table below NVP settings for KRONE cables: Cable Order No. NVP * KRONE Cat 7 S-STP 7053 3 062-25 0.80 KRONE Cat 6 S-STP 7053 2 062-25 0.80 KRONE Cat 6 FTP 7053 2 021-04 0.68 KRONE Cat 6 UTP 7053 2 001-00 0.68 KRONE Cat 5e S-FTP 7053 1 052-25 0.66 KRONE Cat 5 FTP 7053 1 021-04 0.68 KRONE Cat 5 UTP 7053 1 001-00 0.68 KRONE C6 TrueNet UTP 7052 2 110-00 0.70 KRONE C5e TrueNet UTP 7052 1 110-00 0.70 * Note: The correct NVP setting is necessary; it has an influence on the determination of the cable length by the instrument. 23 Notes on the use of hand-held test devices for installation of the KRONE Cat.6 KM8 products Page 6 of 9 December 2001 Agilent WireScope 350 The WireScope 350 performs all tests required by ISO/IEC 11801, for example: § Wiring errors § NEXT § Power Sum NEXT § Return Loss § ELFEXT § Power Sum ELFEXT § Characteristic Impedance § Attenuation § ACR § Power Sum ACR § DC resistance § Length § Delay Skew For further details please refer to the Agilent documents Before you start a large-scale series of measurements go to the Agilent homepage to see whether there are current drivers, etc. for downloading: http://wirescope.comms.agilent.com/default.htm The following releases are the most current ones: WireSope 350: Software Release v2.12 ScopeData Pro: Software v2.12 Accessories: § Permanent Link Interface Adapter N2604A-101 : Includes: § 2 interface adapters § one set Personality module for KRONE KM8 23 Notes on the use of hand-held test devices for installation of the KRONE Cat.6 KM8 products Page 7 of 9 December 2001 Cat 6/5e Channel Adapter N2604A-100: § Includes two interface adapters for use with the WireScope: Basic Link Adapter: § For Krone TrueNet (Link Test Probe N2604A-021) § This adapter cannot be used for the KM8 Required settings: § Type of cable § Category 5e, 6 or 7 § UTP or STP § NVP´s (nominal velocity propagation) are in general already set as instrument default values; otherwise see the table below NVP setting for KRONE cables: Cables Order No. NVP* KRONE Cat 7 S-STP 7053 3 062-25 0.80 KRONE Cat 6 S-STP 7053 2 062-25 0.80 KRONE Cat 6 FTP 7053 2 021-04 0.68 KRONE Cat 6 UTP 7053 2 001-00 0.68 KRONE Cat 5e S-FTP 7053 1 052-25 0.66 KRONE Cat 5 FTP 7053 1 021-04 0.68 KRONE Cat 5 UTP 7053 1 001-00 0.68 KRONE C6 TrueNet UTP 7052 2 110-00 0.70 KRONE C5e TrueNet UTP 7052 1 110-00 0.70 * Note: The correct NVP setting is necessary; it has an influence on the determination of the cable length by the instrument. 23 Notes on the use of hand-held test devices for installation of the KRONE Cat.6 KM8 products Page 8 of 9 December 2001 IDEAL LT8600LT The IDEAL LT8600 performs all measurements required by ISO/IEC 11801, for example: § Wiring errors § NEXT § Power Sum NEXT § Return Loss § ELFEXT § Power Sum ELFEXT § Characteristic Impedance § Attenuation § ACR § Power Sum ACR § DC resistance § Length § Delay Skew For further details please refer to the IDEAL documents. Before you start a large-scale series of measurements go to the IDEAL homepage to see whether there are current drivers, etc. for downloading: http://www.idealindustries.com/dc/LANCableTesters.nsf The following releases are the most current ones: § IDEAL LT8600T: Firmware Version - 2.141 § LT Record Manager (LTRM) Software: 1.122 Accessories: § Permanent Link Interface Adapter (for the exact scope of the delivery contact the manufacturer/ supplier) 23 Notes on the use of hand-held test devices for installation of the KRONE Cat.6 KM8 products Page 9 of 9 December 2001 Cat 6/5e Channel Adapter § Includes two interface adapters for the LT8600T Basic Link Adapter: § This adapter cannot be used with the KM8. Required settings: § Type of cable § Category 5e, 6 or 7 § UTP or STP § NVP´s (nominal velocity propagation) are in general already set as instrument default values; otherwise see the table below NVP settings for KRONE cable: Cable Order No. NVP* KRONE Cat 7 S-STP 7053 3 062-25 0.80 KRONE Cat 6 S-STP 7053 2 062-25 0.80 KRONE Cat 6 FTP 7053 2 021-04 0.68 KRONE Cat 6 UTP 7053 2 001-00 0.68 KRONE Cat 5e S-FTP 7053 1 052-25 0.66 KRONE Cat 5 FTP 7053 1 021-04 0.68 KRONE Cat 5 UTP 7053 1 001-00 0.68 KRONE C6 TrueNet UTP 7052 2 110-00 0.70 KRONE C5e TrueNet UTP 7052 1 110-00 0.70 * Note: The correct NVP setting is necessary; it has an influence on the determination of the cable length by the instrument. . 23 Notes on the use of hand-held test devices for installation of the KRONE Cat. 6 KM8 products Page 1 of 9 December 2001 Notes on the use of hand-held test. suitable § for the KRONE KM8 23 Notes on the use of hand-held test devices for installation of the KRONE Cat. 6 KM8 products Page 5 of 9 December 2001 Cat 6/ 5e