Đang tải... (xem toàn văn)
Đây là hướng dẫn sử dụng phần mềm Mastercam-X4. hướng dẫn có các hình ảnh và ví dụ cụ thể
Router Training TutorialsTo order more books:Call 1-800-529-5517 orVisit www.inhousesolutions.com orContact your Mastercam Dealer Mastercam X4 Training Tutorials Router ApplicationsDate: August 6, 2009Copyright © 1984 2009 In House Solutions Inc. All rights reserved.Software: Mastercam X4 RouterAuthors: Mariana LendelISBN: 978 1 926566 38 2NoticeIn House Solutions Inc. reserves the right to make improvements to this manual at any time and withoutnotice.Disclaimer Of All Warranties And LiabilityIn House Solutions Inc. makes no warranties, either express or implied, with respect to this manual orwith respect to the software described in this manual, its quality, performance, merchantability, or fitnessfor any particular purpose. In House Solutions Inc. manual is sold or licensed "as is." The entire risk as toits quality and performance is with the buyer. Should the manual prove defective following its purchase,the buyer (and not In House Solutions Inc., its distributor, or its retailer) assumes the entire cost of allnecessary servicing, repair, of correction and any incidental or consequential damages. In no event will InHouse Solutions Inc. be liable for direct, indirect, or consequential damages resulting from any defect inthe manual, even if In House Solutions Inc. has been advised of the possibility of such damages. Somejurisdictions do not allow the exclusion or limitation of implied warranties or liability for incidental orconsequential damages, so the above limitation or exclusion may not apply to you.CopyrightsThis manual is protected under the copyright laws of Canada and the United States. All rights arereserved. This document may not, in whole or part, be copied, photocopied, reproduced, translated orreduced to any electronic medium or machine readable form without prior consent, in writing, from InHouse Solutions Inc.TrademarksMastercam is a registered trademark of CNC Software, Inc.Microsoft, the Microsoft logo, MS, and MS DOS are registered trademarks of Microsoft Corporation;Mastercam Verify is created in conjunction with Sirius Systems Corporation; Windows, Windows 95, andWindows NT are registered trademarks of Microsoft Corporation.AcknowledgmentsWe would like to thank the In–House Solutions team for its recommendations and input. TABLE OF CONTENTSGetting Started . A 1Graphic User Interface . ANavigate Through Mastercam ASetting the Toolbar States ASetting the Grid A1245Tutorials . 1 1Tutorial #1, 2D Geometry and Contouring . 1 1Tutorial #2, 2D Geometry, Pocket and Contouring 2 1Tutorial #3, 2D Geometry, Drilling and Contour 3 1Tutorial #4, Door 4 1Tutorial #5, 2D Geometry, Contour, Pocket, Engraving and Chamfer . 5 1Tutorial #6, Importing a Bitmap using Raster to Vector Translator . 6 1Tutorial #7, Creating and Using a Profile Bit For Moldings 7 1Tutorial #8, Nesting 8 1Tutorial #9, Creating and Using a Profile Bit for Table Top, Metric Exercise 9 1General Notes . B1Default Key Assignments BCustomizing BData Entry Shortcuts BCreating Geometry in 3D BChaining BWindow Selection . BToolpath Manager B23923262932Tool Library . C 1Creating and Editing a Router Tool Library C 2 TUTORIAL SERIES FORTUTORIAL # 22D GEOMETRY, POCKET & CONTOUR ROUTER X4TUTORIAL 2Objectives:The Student will design a 2 dimensional wireframe drawing by:Creating a rectangle using the 1 point method.Creating parallel lines, by defining the offset direction and distance.Creating arcs using polar command.Creating a line knowing the endpoints of the line.Trimming 1 entity to another existing entity.Creating arcs knowing the radius and the center points of the arcs.Trimming two entities up to the intersection point between the entities.Deleting extra construction lines.Offsetting entities with a given distance.Mirroring existing geometry to complete a part.Modifying an entity by breaking it in two pieces.Creating fillet radii.The Student will create a 2 dimensional milling toolpath consisting of:A 2 dimensional contour.Machine the two pockets in one operation.Remachining the two pockets using a smaller tool that will remove the material only in the areawhere the previous tool could not fit.The Student will check the toolpath using Mastercam’s Verify verification module by:Running the Backplot function.Defining a 3 dimensional rectangular block the size of the work piece.Running the Verify function to simulate machining the part on the screen.The Student will generate the NC file by:Running the Post processor.Page 2 2 ROUTER X4TUTORIAL 2GEOMETRY CREATIONSetting the toolbar statesBefore starting the geometry creation we should customize the toolbars to see Setting the ToolbarStates to create the geometry and machine a 2D part. on page A 4 in the User Notes.Make sure that the Grid is enabled as it will show you where the part origin is. See Setting the Gridon page A 5Operations Manager to the left of the screen can be hidden to gain more space in the graphic areafor design. Press Alt + O to hide it.Due to the fact that this drawing is symmetrical in the Y axis, you will only draw 1/2 of the total partand use the mirror function to complete the partPage 2 3 . Router Training TutorialsTo order more books:Call 1-8 0 0-5 2 9-5 517 orVisit www.inhousesolutions.com orContact your Mastercam Dealer Mastercam