XG-3300 自动立式插件机操作说明书 l Preface l l This" operates the operation instruction" Enclose one at random, please keep this manual, in order to consult at any time l Please must read a manual carefully conscientiously in front of operating this apparatus l Because the renewal of technology and special requirement for the products, some material objects of product may be different to some extent with the manual, please subject to products material object, we will supplement and add as much as possible to prove l When the apparatus uses normally, please keep certain space in front and at the back of this apparatus, as operating and maintaining the necessary space In addition, please don't make and hinder heat from discharging the arrangement of the space to this apparatus l The environment for use of the apparatus: The temperature is: 5- 25 C, the relative humidity is: 20- 95%, is not penetrated directly by the sunshine, will not form the dew and will not spatter the place that water, oil, chemistry are liquid l The technical staff who operates and maintains this machine must know and use the computer l The computer that disposes on this machine can only be used for this machine, forbids using as it, forbid inserting other movement memories which carries the virus in this machine, so as not to destroy the control system l Tight and anti-virus U one disposed at random is invaded, forbid using on other computers at will l For the personal security, the apparatus is while running or awaiting the opportune moment, please don't open Qianmen and roller chain and the head protection cover stands on condition that take any safety measure, forbid clothes, four limbs,etc close to the mechanical sport position, otherwise, may bring the unexpected injury to life l The power of repeated switch, will become one of the reasons why the apparatus produce the trouble In the power OFF ' Cut off) And then, please carry on the power ON (open) again through more than 20 seconds l Don't let the apparatus struck strong vibrations, otherwise may cause the trouble l While cutting off the apparatus power, please carry on systematic withdrawal / 东莞市新泽谷机械有限公司 - - www.sciencgo.com XG-3300 自动立式插件机操作说明书 shut-down course in following order, if does not carry out this course but cut off or restart, will make the data unable to get intact save the power directly, may cause the damage of the hard disk at the same time Withdrawal / shut-down course: Withdraw from the application program and withdraw from Windows, cut off the apparatus power l If delay using this apparatus, please keep the apparatus in the following places: The ambient temperature is that (0-40) Centigrade degree, relative humidity is that (20-95) %, is not penetrated directly by the sunshine, will not form the dew and will not spatter the place that water, oil, chemistry are liquid For being dustproof, can consider taking and hiding the measure (such as wrapping the cover) ,But dampproof Please contact us in the place not understood, make sure not to operate blindly 第一章 Note: Please pay attention to the above-mentioned items! 第二章 第三章 第四章 第五章 第六章 Summary XG-3000 serial and vertical the intersection of plug-in package and plane different kind ' 2.5mm and 5mm) Weave bring vertical electronic element ( a slice of electric capacity of electric capacity, porcelain, LED,etc.) Electrolyze With LED in bulk, grades in order of procedure that presumes in the material of the roller chain is inserted first, then, the head organization of the plug-in package inserts the electronic element in the circuit board, and cut the foot, fixed This apparatus fixes plug-in package axle organization's level and does not move, by the movements of X, Y organization, realize the accurate plug-in package in every area on P C B, the angle of the plug-in package is realized by the working bench rotary table, turning of head corner motor RH, corner motor RB of the base The movements of all machines are come to control by a computer This serial 东莞市新泽谷机械有限公司 - - www.sciencgo.com XG-3300 自动立式插件机操作说明书 vertical machines have several following great advantages: Wholly computer controled, the whole the intersection of Chinese edition and operating system, based on the intersection of Windows and platform, easy to operate swift simple easy to learn Adopt the visual technology of the machine, online automatic programming, rectify a deviation automatically, distinguish MARK to click automatically, have improved the automatic intensity Arrange material stand location every 10 station one, enable convenient choice to users their Adopt AC servo system, optimize the circuit, excludes from the unstability that causes because of circuit trouble, realize and stabilize the high speed, save the goal of the energy It is to meddle in the direction -360 degrees, increment is degree The working bench can be rotated clockwisely and anticlockwisely and arbitrarily 1,Specification parameter of the Specification parameter machine 东莞市新泽谷机械有限公司 - - www.sciencgo.com XG-3300 自动立式插件机操作说明书 Project Theory speed 18000 / hour (software system upgrade and can raise speed) Insert the bad rate Smaller than 1000PPM Meddle in the direction 0- Increment of 360 degrees is degree Span of lead wire One pair of intervals 2.5mm/5.0mm Size of the base plate Minimum 50mm *50mm, biggest 450mm *450mm Thickness of the base plate 0.79-2.36mm Component The maximum height is 20mm, the largest diameter is specification 10mm, the largest pin diameter is 0.8mm Condenser, transistor, triode, the intersection of LED and Component kind light, key switch, resistance, connector, coil, potentiometer, the intersection of fuse and flat, fuse silk,etc to be vertical to arrange and lead one The component lead wire cuts the foot 1.5¡À 0.3mm (short foot knife) ,2.0¡À 0.3mm (long foot knife) length The component lead wire curves the angle 10-35 degrees are (adjustable) of foot Quantity of material 60 stations (recommend use to stand and count) ,Available ' station 10-100 stations) Machine size (long * It is wide and * high) Material station measurement Host computer size 1800mm * 1600mm* 2000mm 500mm* 600mm* 760mm Machine weight 2000KG (40 stations) Use the power 220V, AC is (single-phase) 50/60HZ, 2.0KVA; The system protects Use the power Use the atmospheric pressure Gas consumption 东莞市新泽谷机械有限公司 Incessant power (UPS) Dispose, can run for 15 minutes after cutting out 1.6KW is (energy-efficient) 0.6 0.8MPA 0.3 cubic meters per minute - - www.sciencgo.com XG-3300 自动立式插件机操作说明书 Use the ambient temperature 5-25 degrees Machine noise 80 decibels Correct the way in the location of hole The visual system of the machine, many point MARK visions Drive the system Servo AC, AC motor Input way of the data USB interface is input (EXCEL file form) , Control system are corrected Operate interfaces (WINDOWS system controls the platform) in Chinese 1MM interval between the component noumenonn, sticks to Component density a component and hole the distance can not be smaller than 3mm Way of operating of working bench The circuit board transports the way Clockwise and anticlockwise Manually / automatic and available 2,Mechanical part 1) Framework And rank material vice machines and foundation shelves to make up from the plug-in package host computer shelf The framework unit formed basic structure of the apparatus, the framework was welded and formed with the square iron pipe of 150* 100 and 50* 50, the structure is rational, it is reliable to stabilize The intersection of four corners and installation in framework have, resist shock foundation, the height of the foundation can be adjusted, level degree used for adjusting the machine 2)X, Y working bench organization This machine is to move by the workbench which puts PCB, realizes that carries on the plug-in package to PCB each area Each working bench organization is done the orbit by two pieces of hard steel axle, install a set of ball vice and servo motors of guide screw as driving in the middle, two axles of the guide screw are fixed in end, the motor links up with it through taking synchronously, the guide screw nut and platform board is fixedly connected The motor drives the guide screw to rotate, the guide screw drives guide screw nut and platform to rectilinear motion X, Y install 东莞市新泽谷机械有限公司 - - www.sciencgo.com XG-3300 自动立式插件机操作说明书 straight the intersection of negative pole and limit, measure photoelectric switch and zero, measure the photoelectric switch each at the the intersection of working bench and organization Organization's sports go beyond the first terminal motor and moderate, go beyond the second terminal motor to stop after moderating, avoid producing the destructive impact to the servo system Zero measure photoelectric switch, determine the intersection of workbench and the intersection of organization and position when shutting down X working bench organization installs on a platform of host computer, Y working bench mechanism installed on X working bench organization, working bench platform adopt, import the aluminium material while being good, realize light quantization Set up a round rotary table in the platform of organization of working bench Y, the round rotary table is held up by four bearings of horizontal installation, restricted the location to it all around by four bearings installed vertically Each install a localization card seat with Model V mouth correspondingly around the disc, under the normality, localization organization installed on the platform " The tongue " Stretch out, contact with which orientate the intersection of Carlos and flat the intersection of Model V and mouth closely, make a reservation to the disc Orienting the organization is mainly applied the air cylinder, a scalable one by two forms " The tongue " And the retainer plate,etc make up When the revolving stage needs rotating, the air cylinder stretches out, " tongue " Contract, and move out of contact with card seat Rotation of disc drive by motor by revolving stage, the intersection of revolving stage and through bring with first scalable round rounds of organization linking synchronously motor Install an air cylinder on round organizations, when the disc needs rotating, this air cylinder stretches out, the round wheel keeps in touch with the edge of the disc closely, the rotation of the motor is to drive the rotation of the disc 3)Head organization The head organization inserts the chain the component on to send the noumenonn of the plug-in package, and insert in the circuit board H axle motor connects with horizontal gear axle through the synchronous tape, axle of the gear and rack clench the teeth, the rack is installed on a pair of straight lines bearing stand, the straight line bearing is fixed on two pieces of hard steel axle, the hard steel axle is fixed on main fact, countershaft seat And install high-speed guide screws and nuts on the straight line bearing seat, the top of the guide screw is fixed on straight line bearing seat of the top, the underpart of the guide screw connects and presses 东莞市新泽谷机械有限公司 - - www.sciencgo.com XG-3300 自动立式插件机操作说明书 material pole, this guide screw and straight line bearing seat can be slipped on the hard steel axle freely; The guide screw nut is locked on the bearing through a nut set, and fix and install a gear on the nut, this clench the teeth by gear and one vertical the intersection of gear and axle, vertical gear axle and the servo motor P link through synchronous strip also, the rotation of the motor P can drive the upper and lower sports of the guide screw, at the time of the upper and lower sports of the rack, guide screw and the nut, with upper and lower sports Make and set up a rotatory bearing in the straight line bearing seat, the hollow plug-in package main pole connects with this bearing, the main pole is oriented it by two bearings installed horizontally Install bearing in the mainly hard steel axle stand, main pole set and bearing equipped with synchronous wheel are fixedly connected, the main pole is crossed the main pole set, synchronous wheel connects with motor RH through the synchronous tape, the main pole follows to rotate too when the motor is rotated, realize different angle plug-in packages The underpart of the main pole installs the noumenonn of the plug-in package Insert the material and unload the material organization on the noumenonn When CTA organization sends the material, insert the material organization and grip the material; When inserting the component, unload the material organization and unload the original paper from clip To give material slippery pieces of front to have, give glassware arcuately CTA, hand over on the glassware installing the material shovel arcuately, the underparts are installed a set of clips, the roller chain is worn among them; Give material slip piece connect with linear the intersection of slide rail and activity, slide rail connect with air cylinder, the intersection of air cylinder and work give material, slip, take exercises before and after the yuan, send to inserting the material organization and returning of noumenonn of the plug-in package on inserting the original paper from the chain of the roller chain CTA organization install in the middle of tray, both sides their respectively install a sprocket While working, send to inserting the material organization of noumenonn of the plug-in package on inserting the original paper from the chain of the roller chain in CTA organization, then go back to the location; The motor RH knows but rotation according to the need for inserting the angle, wave the angle of the original body; H axle motor is rotated, the downward sports of the rack, the noumenonn of the plug-in package and pressing the downward sport together of material pole; The 东莞市新泽谷机械有限公司 - - www.sciencgo.com XG-3300 自动立式插件机操作说明书 motor P is rotated, presses the downward sports of material pole, inserts original paper in the hole on board of the circuit, and then, press material pole back to the location, and then go back to the location with rack 4)Base organization Base organization to roll over curved cutting surplus pinning of the component inserting the intersection of circuit and component of board in Install and cut the foot in the noumenonn of the base, is cutting both sides of of foot install one respectively measure excellently, wonderful and noumenonn and cut the intersection of foot and to be insulating this normally, cut the intersection of foot and one hundred sheetses of movement put in place, the one hundred sheets of body keeps in touch with measuring excellently closely, with " ground " of the machine Form the return circuit The noumenonn is fixedly mounted on main pole of the base, the main pole is connected with one set of activities of main pole, the main pole puts in synchronous gear, main pole set and bearing in the fix are fixedly connected, the synchronous wheel is linked with the motor RB through the synchronous tape Sharing a set of organizations with one cutting the foot from head to foot of the base Rise air cylinder, air cylinder connect head, connect the intersection of column and son, air cylinder slip piece, connect hair, sell son, the air cylinder connects of one, the air cylinder connects of one, air cylinder connecting rod, cut foot air cylinder,etc make up While working, the motor RB is rotated, noumenonns turns into the angle needed, job base noumenonn of the air cylinder of rising and rises in the base, after rising in place, cut the foot air cylinder work, the air cylinder connecting rod gives and cuts the foot exert pressure, cut the foot cut off pin of the original paper 5)A tight organization relaxes degree roller chain for keeping the roller chain appropriate Made up of three sets of sprockets, present " products " Shape is distributed, the wheel on the left except the upper and lower positions are adjustable, other positions are fixed and non-adjustable The middle with one of right regulate position before the all right wheel, come, regulate elasticity of roller chain When installing the roller chain, a set of middle wheels compress the spring to be limited on two axles through two, axle fix on axle stand,axle flat can before and after regulate,regulate by spiral shell pole for each in axle flat also, another end of spiral shell's pole withstands a pressing plate, the pressing plate is fitted on two axles and and compress the spring to keep in touch closely, regulate spiral shell's pole, can regulate the working length of the spring, just regulates the deformation amount when the roller chain receives strength 东莞市新泽谷机械有限公司 - - www.sciencgo.com XG-3300 自动立式插件机操作说明书 6)The paper-cut is brought the organization Insert the paper tape of component on to cut off partly through chain of position this Air cylinder and slippery pieces of connection, slip on the piece installing, cutting, pressing one hundred sheets, shelling the intersection of paper and mainly, slipping one is pressing and covering and regulating pressing stretches out the terminal regulation piece and regulates spiral shell's pole; There is; The back of cutting one hundred sheets has roller chain guides; There is a bearing, the side limit location to the roller chain opposite to the guide; Can push down the wheel that insert of chain in the chain is inserted, the wheel inserts " elasticity " with the chain under the function of the spring Keep in touch, insert the location of limit to the chain The air cylinder movements while working, slip one move forward, press the knife and push down the pin of the component forward and first, it is higher than the paper tape which will cut off the position to strip from top to bottom to shell the paper, cut cut off the pin of the component again, just there is no paper on the component pin cut 8)The roller chain drives the organization It is a rotatory organization of chain drive-belt Made up of servo motor, planet gear gearbox, diaphragm type shaft coupling, initiative sprocket,etc Install, have eight even photoelectricity of slot measure one by one in initiative the intersection of axle and end of sprocket, used for measuring a location of the roller chain 9)Assign the head organization Arrange, bring electronic element from arrange, take one by one cutting off, separating, at a fast, accurate one send chain of roller chain to, insert The intersection of roll and the intersection of material and gear install in weave, carry, lead the intersection of tail and end of board to, electromagnetic valve, air cylinder make up install in the intersection of the station and the intersection of location and the intersection of tail and end of the noumenonn, air cylinder exert oneself pole yuan link through connect head and slip voluntarily by one activity, slip voluntarily the intersection of another end and installation of piece have bifid to push the intersection of material and slice, measure board, side installation have main blade to cut the paper, slip voluntarily piece back and still vertical to install first axle, the axle is connected with the connecting rod activity, another end of the connecting rod is connecting pawl and ratchet wheel organization, another end of axle on the ratchet wheel is connecting roll material rubber tyer, have, weave, lead material pressing plate and one pack of blades to cut paper by the side of rubber tyer, a blade is installed on an adjustable knife seat, used for regulating it and interval 东莞市新泽谷机械有限公司 - - www.sciencgo.com XG-3300 自动立式插件机操作说明书 among the main blades Slip voluntarily nearby activity of piece install one piece driven to slip piece, top its install, cancel the material claw by one the intersection of Z and style of calligraphy, collude at another end of the material claw and that is to limit the journey of one drivenly to slip from two pieces of locating stud limit location, there are tooth's sockets on this one end, tooth's socket and driven activity that slips in one sell and clench the teeth, the pin is compressed the spring to withstand by one, another end of the spring is connected with the locating stud Return installation, lack material, measure stretch on packs of the intersection of blade and seat, have material put in place, measure slice and measure the intersection of circuit and conductive the intersection of copper and skin of terminal surface of board, keep in touch, form the return circuit, otherwise, form the broken circuit Air cylinder stretch out work, slip voluntarily pieces of have cut knife mainly and pack cut knife, arrange, lead the material cut off put in place; Meanwhile, terminal surface of yuan apply jointly, orient, clamp the component; Bifid push away material a block of front and material, insert, keep in touch first, insert, orientate the material first, thereupon, push the component to the chain in the clip inserted, cancel the material claw to open; The air cylinder is withdrawn, organization's sports of ratchet wheel, drive the roll material rubber tyer to rotate an angle, send a component to and cancel it in the material claw again, the air cylinder acts again Circulate so 3,The electricity, air control the part Offer kinetic energy and control signal for machine The movement orders of all of this machines are to import and export through the computer The testing signal of the machine inputs the computer through I\O board, the order signal of movements is input into I\O board or server by the computer This machine uses 220 V AC, 24 volts and volts direct current Allocate UPS alternating current source Alternating current source have, leak electricity switch at the bus, consist of insurance in charge of at the every branched circuit; The direct current is offered by power of switch The earth connection system must be normal, reliable Every one exchanges the servo motor controlled by a server Various servo parameters can be read or adjusted in the screen of the server directly, can also read or adjust on the computer through the specialized software Can reveal the trouble code of the servo system, realize servo " diagnose by oneself " on the screen of the server Source of the gas of machine by angry to accuse of, make up, 东莞市新泽谷机械有限公司 - 10 - www.sciencgo.com XG-3300 自动立式插件机操作说明书 After zero switch touch off, machine stop, continue, run The revolving Change the stage small revolving stage board is broken small board The intersection Change the of zero and photoelectric abnormal signal, switch, check photoelectric the the circuit intersection of switch and broken or circuit trouble The coordinate Adjust and work Bring too loose Adjust the walks in the well for some synchronously elasticity of the location time synchronous strip Walk in the It is not tight to Change and location again embrace the embrace the hoop hoop The signal line of Change encoder is broken The motor or Change driver is broken Drive and lock Change the rotary table electromagnetic valve out of Rotary table The rotary table order is locked and Rotate the line Check and does not brokenly change with the release, the 东莞市新泽谷机械有限公司 universal meter - 174 - www.sciencgo.com XG-3300 自动立式插件机操作说明书 rotary table is Two stingy jars Check and not moved which release revitalize the rotary table can't open and let the rotary table be rotated to become flexible and result in locking the device in place The motor or Change relay of the revolving stage is out of order Note: The machinery that the mechanical trouble clearing please consult chapter five adjusts the part Second, mechanical figure: 1,The plane figure of the machine: 东莞市新泽谷机械有限公司 - 175 - www.sciencgo.com 0.8M 1.8M XG-3300 自动立式插件机操作说明书 1.71M 气源引入位置 配气管?12x8.5 0.2M 总电源引入位置,配 线(L+N+E)3x2.5mm 0.5M 0.5M 1.54M 机器总长(L)=1.54M+0.5M+ 总站数 10站 x0.5M+0.2M 机器电源开关 位置 2,The electricity controls the wiring general drawing: 东莞市新泽谷机械有限公司 - 176 - www.sciencgo.com XG-3300 自动立式插件机操作说明书 XG3K-立式机(第一代总接线图) NFB1 L N UPS FU1 5 6 插座 FU2 21 FU4 电脑主机 液晶显示器 FU3 +24V、P - 24 10 + FU6 FU5 11 6 +5V、P 23 27 28 29 30 J4 22 J1 J2 12 13 J3 端子TB15-12 ES 27 25 I/O·A-IN1 93 26 滤 波 器 光源 光 电 开 关 照 明 C3 14 15 风扇 转 台 感 应 24 NFB7 NFB3 NFB2 16 I/0·A·X6 + 电源 GND 13 29 41 31 - X5 X5 X6 G 25 伺服器 X NFB4 17 15 电源 I/0·A·X7 35 GND + - X2 13 29 41 X5 X5 G X6 NFB5 15 伺服器 Y 18 I/0·B·X9 39 电源 G ND + - X2 13 29 41 15 链条 X5 伺服器 X5 X6 G C 43 + 电源 GND - X2 13 29 41 15 X5 X5 X6 G 22 NFB6 19 I/0·B·X7 NFB8 21 伺服器 RH 20 I/0·A·X9 47 + 电源 GND - X2 13 29 41 15 X5 X5 X6 G 伺服器 RB 15 I/0·A·X8 51 + 电源G ND 13 29 41 X5 X5 X2 X6 G 伺服器 P I/0·B·X8 55 电源 GND + 13 29 41 X5 X5 伺服器 X2 X6 G B X2 26 38 34 C1 37 33 C2 42 41 46 45 50 49 54 53 57 C4 I/O·A-OUT1 C5 I/O·A-OUT9 M M C6 I/O·A-OUT10 编码器 东莞市新泽谷机械有限公司 编码器 M 编码器 - 177 - M 编码器 M M 编码器 编码器 www.sciencgo.com M 编码器 XG-3300 自动立式插件机操作说明书 XG3K-立式机气控示意图 气控组合 电磁阀 吹线脚电磁阀 吹线脚气缸 铲料电磁阀 铲料气缸 转台压轮电磁阀 转台压轮气缸 转台锁定气缸1 转台锁定电磁阀 转台锁定气缸2 站位电磁阀 东莞市新泽谷机械有限公司 - 178 - www.sciencgo.com XG-3300 自动立式插件机操作说明书 XG3K-立式机电气控制示意图 伺服器 光电开关 大I/0-A 转台 面板 伺服器 大I/0-B 振动盘 电脑 光电开关 小I/0-1 转台 小I/0-2 面板 小I/0 直流5V 电子分向检测板 夹子 直流24V AV-220V 直线调速器 直线送料器 AV-220V 继电器 大I/0-B 东莞市新泽谷机械有限公司 - 179 - 振动盘调 速器 www.sciencgo.com 振盘 XG-3300 自动立式插件机操作说明书 XG3K-立式机转台九针插头接线图 I/O板 (九针接头) +24V -24V 零位检测 +24V -24V 转台到位 3 转 台 感 应 小 板 转台开锁电磁阀 转台压轮电磁阀 M 东莞市新泽谷机械有限公司 转台马达 - 180 - www.sciencgo.com XG-3300 自动立式插件机操作说明书 XG3K-立式机转台马达继电器接线图 J5 继电器 正转 J6 继电器 反转 N0 常开 NC 常闭 C5 J5线圈 IN4007 C6 J6线圈 C5 M 马达 J6 25 25 J6 NC62 110 DC24 22 22 N051 110 NC63 112 N052 112 J5 NC51 25 114 115 113 J5 114 NC52 22 M 111 N061 113 N062 115 DC24 111 I/0 C6 ·A-OUT9 I/0 ·A-OUT10 IN4007 东莞市新泽谷机械有限公司 - 181 - www.sciencgo.com XG-3300 自动立式插件机操作说明书 3,The computer controls the sketch map: 东莞市新泽谷机械有限公司 - 182 - www.sciencgo.com XG-3300 自动立式插件机操作说明书 4,I/O plank wires tables: I/O A board wiring diagram Interface board Signal mark Signal name Label serial number Interface board Signal mark Signal name Label serial number A-* 8-1 PULH+ H server X5-3 51 A-* 6-1 PULX+ X server X5-3 31 A-* 8-2 PULH- H server X5-4 51 A-* 6-2 PULX- X server X5-4 31 A-* 8-3 DIRH+ H server X5-5 51 A-* 6-3 DIRX+ X server X5-5 31 A-* 8-4 DIRH- H server X5-6 51 A-* 6-4 DIRX- X server X5-6 31 A-* 9-1 PULRH+ RH server X5-3 43 A-* 7-1 PULY+ Y server X5-3 35 A-* 9-2 PULRH- RH server X5-4 43 A-* 7-2 PULY- Y server X5-4 35 A-* 9-3 DIRRH+ RH server X5-5 43 A-* 7-3 DIRY+ Y server X5-5 35 A-* 9-4 DIRRH- RH server X5-6 43 A-* 7-4 DIRY- Y server X5-6 35 A-* 5-1 OUT1 Flashing lamp 63 A-* 6-6 ELX+ X + limit 58 A-* 5-2 OUT2 Spare A-* 6-7 ELX- X - limit 59 A-* 5-3 OUT3 Green light 64 A-* 6-8 SDX+ X + moderates 61 A-* 5-4 OUT4 Yellow light 65 A-* 6-9 SDX- X - moderate 62 A-* 5-5 OUT5 Red light 66 A-* 3-0 ORGX X Origin 60 A-* 5-6 OUT6 Foot cutting device 73 OUT7 The revolving stage is locked and turned on 74 A-* 7-6 ELY+ Y + limit 68 A-* 5-7 The revolving A-* 7-7 ELY- Y - limit 69 A-* 5-8 OUT8 stage presses the wheel A-* 7-8 SDY+ Y + moderates 71 A-* 5-9 OUT9 Clockwise 89 A-* 7-9 SDY- Y - moderate 72 A* -5-10 OUT10 Counter-clockwise 90 A-* 3-1 ORGY Y Origin 70 A* -5-11 OUT11 Paper-cut 91 A-* 8-6 ELH+ H + limit 78 A-* 5-12 OUT12 Give the material 92 IN5 The plug-in package measures 96 A-* 2-6 IN6 The plug-in package measures 97 A-* 2-7 IN7 Start 98 A-* 2-8 IN8 Stop 99 A-* 2-9 IN9 100 102 A-* 8-7 A-* 3-2 ELH- ORGH 东莞市新泽谷机械有限公司 H - limit H Origin 79 80 - 183 - A-* 2-5 A-* 2-10 IN10 Give the glassware B A-* 2-11 IN11 The revolving www.sciencgo.com 75 XG-3300 自动立式插件机操作说明书 stage is put in place A-* 2-12 IN12 Zero's location of the revolving stage 103 101 ORGRH RH origin 84 A-* 3-13 IN13 Give the glassware F IN1 Emergency switch 93 A-* 3-14 IN14 Under the base 104 IN2 The head is safe 88 A-* 3-15 IN15 Assign the head to be left 105 A-* 2-3 IN3 The protecting cover is safe 94 A-* 3-GND GND 24 VDC - 23 A-* 2-4 IN4 Head switch 95 A-* 3-VDD VDD 24 VDC + 24 A-* 3-16 IN16 Assign the head to be right 106 Interface board Signal mark Signal name Label serial number B-* 8-1 PULP+ P server X5-3 55 B-* 8-2 PULP- P server X5-4 55 B-* 8-3 DIRP+ P server X5-5 55 B-* 8-4 DIRP- P server X5-6 55 B-* 9-1 PULC+ C server X5-3 39 A-* 3-3 A-* 2-1 A-* 2-2 A-* 3-G+1D GND Ground wire X X Motor Y H Y Motor Head motor of the plug-in package RH On the corner motor I/O B board wiring diagram Interface board Signal mark Signal name Label serial number B-* 7-1 PULRB+ RB server X5-3 47 B-* 9-2 PULC- C server X5-4 39 B-* 7-2 PULRB- RB server X5-4 47 B-* 9-3 DIRC+ C server X5-5 39 B-* 7-3 DIRRB+ RB server X5-5 47 B-* 9-4 DIRC- C server X5-6 39 B-* 7-4 DIRRB- RB server X5-6 47 43 OUT1 Spare 13 10 44 OUT2 Spare 14 11 45 OUT3 Spare 15 12 46 OUT4 Spare 16 13 B-* 5-5 OUT5 Base 17 18 14 B-* 5-6 OUT6 Blow the line foot 15 B-* 5-7 OUT7 Spare 19 16 B-* 5-8 OUT8 Spare 20 东莞市新泽谷机械有限公司 - 184 - www.sciencgo.com XG-3300 自动立式插件机操作说明书 17 B-* 5-9 OUT9 Spare 21 18 B-* 5-10 OUT10 Spare 22 B-* 3-1 ORGRB RB origin 83 53 OUT11 23 B-* 3-2 ORGP P Origin 85 54 OUT12 24 21 55 22 56 IN5 Lack the material and measure 21 IN6 Lack the material and measure 22 Lack the material and measure 23 23 57 IN7 24 58 IN8 24 25 59 IN9 25 26 60 IN10 26 27 61 IN11 27 28 62 IN12 28 B-* 3-3 ORGC C Origin 82 63 IN13 29 B-* 2-1 IN1 Cut the foot measure 108 64 IN14 30 B-* 2-2 IN2 Mend the material 109 65 IN15 31 IN3 Shake and measure B-* 3-GND GND 24 VDC - 23 B-* 2-4 IN4 Shake and measure B-* 3-VDD VDD 24 VDC + 24 B-* 3-GND GND Ground wire 68 IN16 B-* 2-3 RB Under the corner motor Push Press the material motor C Motor of the roller chain -Without while shaking the plate, will shake and measure, lack signal and " ground " that the material will be measured Connect short The location board wiring diagram stands ' 30 stations) P32C32 card CON1 (37 stitches of ports of the card) 东莞市新泽谷机械有限公司 - 185 - www.sciencgo.com 32 XG-3300 自动立式插件机操作说明书 Interface board 10 11 12 13 14 15 16 17 18 19 CON2 Interface board Signal mark GND Signal name 24V (-) A station is INPUT0 input stations are INPUT1 input stations are INPUT2 input stations are INPUT3 input stations are INPUT4 input stations are INPUT5 input stations are INPUT6 input stations are INPUT7 input stations are INPUT8 input 10 stations are INPUT9 input 11 stations are INPUT10 input 12 stations are INPUT11 input 13 stations are INPUT12 input 14 stations are INPUT13 input 15 stations are INPUT14 input 16 stations are INPUT15 input Ground of COM1A signal Ground of COM1B signal (37 stitches of ports drawn) Signal mark Signal name GND 24V (-) 17 stations are INPUT16 input INPUT17 18 stations are 东莞市新泽谷机械有限公司 - 186 - Interface board 20 Signal mark GND 21 OUTPUT0 22 OUTPUT1 23 OUTPUT2 24 OUTPUT3 25 OUTPUT4 26 OUTPUT5 27 OUTPUT6 28 OUTPUT7 29 OUTPUT8 30 OUTPUT9 31 OUTPUT10 32 OUTPUT11 33 OUTPUT12 34 OUTPUT13 35 OUTPUT14 36 OUTPUT15 Signal name 24V (-) A station is exported stations are exported stations are exported stations are exported stations are exported stations are exported stations are exported stations are exported stations are exported 10 stations are exported 11 stations are exported 12 stations are exported 13 stations are exported 14 stations are exported 15 stations are exported 16 stations are exported 37 VC 24V (+) Interface board 20 Signal mark GND 21 22 OUTPUT16 OUTPUT17 Signal name 24V (-) 17 stations are exported 18 stations are www.sciencgo.com XG-3300 自动立式插件机操作说明书 INPUT18 INPUT19 INPUT20 INPUT21 INPUT22 INPUT23 10 INPUT24 11 INPUT25 12 INPUT26 13 INPUT27 14 INPUT28 15 16 17 18 19 INPUT29 INPUT30 INPUT31 COM2A COM2B 东莞市新泽谷机械有限公司 input 19 stations are input 20 stations are input 21 stations are input 22 stations are input 23 stations are input 24 stations are input 25 stations are input 26 stations are input 27 stations are input 28 stations are input 29 stations are input 30 stations are input Ground of signal Ground of signal - 187 - 23 OUTPUT18 24 OUTPUT19 25 OUTPUT20 26 OUTPUT21 27 OUTPUT22 28 OUTPUT23 29 OUTPUT24 30 OUTPUT25 31 OUTPUT26 32 OUTPUT27 33 OUTPUT28 34 35 36 37 OUTPUT29 OUTPUT30 OUTPUT31 VC exported 19 stations are exported 20 stations are exported 21 stations are exported 22 stations are exported 23 stations are exported 24 stations are exported 25 stations are exported 26 stations are exported 27 stations are exported 28 stations are exported 29 stations are exported 30 stations are exported 24V (+) www.sciencgo.com XG-3300 自动立式插件机操作说明书 东莞市新泽谷机械有限公司 - 188 - www.sciencgo.com ... Corner: According to the procedure requirement corner while checking coordinates manually, in order to check coordinates manually 东莞市新泽谷机械有限公司 - 21 - www.sciencgo.com XG-3300 自动立式插件机操作说明书 Correct:... output reaction signal Mend a switch control signal of mending one manually After inserting the component on the circuit board manually, click " mends one " on the panel The switch, cut the foot... of the safe machine of the guardrail When opening the door, if does not change the safety switch manually, output low level, the machine in the work stops running The head switch is that the making