General rules of electrical installation design

11 483 0
General rules of electrical installation design

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

Thông tin tài liệu

THE UNIVERSITY OF TECHNICAL EDUCATION THE UNIVERSITY OF TECHNICAL EDUCATION HO CHI MINH CITY HO CHI MINH CITY FACULTY OF ELECTRICAL FACULTY OF ELECTRICAL & ELECTRONICS & ELECTRONICS ENGINEERING ENGINEERING DIVISION OF INDUSTRIAL ELECTRICSITY DIVISION OF INDUSTRIAL ELECTRICSITY Subject : General rules of electrical installation design Subject : General rules of electrical installation design Name : Nguyễn Thanh Sơn Name : Nguyễn Thanh Sơn ID:05102103 ID:05102103 Ho Chi Minh City 2/21/2009 Ho Chi Minh City 2/21/2009 Objective and content Objective and content -Objective : After I finished this subject ,every body can understand more detail of electrical installation design and I have an good job when I graduated. -Content : + +Definition of voltage ranges +Standards +Quality and safety of an electrical installation +Initial testing of an installation +Periodic check-testing of an installation +Environment Definition of voltage ranges Definition of voltage ranges IEC voltage standards and recommendations The nominal voltage of existing 220/380 V and 240/415 V systems shall evolve toward the recommended value of 230/400 V. -First step, 220/380 V systems →230/400 V (+6%,-10%) and 240/415 V systems → 230/400 V (+10%,-6%). -At the end of this transition period, 230/400 V systems (±10%) should have been achieved. -Apply also for 380/660 →400/690 V Standards Standards This Guide is based on relevant IEC standards, in particular IEC 60364. -IEC 60364-4-41 - Protection for safety - Protection against electric shock -IEC 60364-4-42 - Protection for safety - Protection against thermal effects. -IEC 60947-1 Low-voltage switchgear and control gear - General rules -IEC 60947-2 Low-voltage switchgear and control gear - Circuit- breakers. -IEC 60479-1 Effects of current on human beings and livestock - General aspects…etc. Quality and safety of an electrical installation Quality and safety of an electrical installation -Quality and safety will be assured only if: +The initial checking of conformity of the electrical installation with the standard and regulation has been achieved . + The electrical equipment comply with standards. +The periodic checking of the installation recommended by the equipment manufacturer is respected. Initial testing of an installation Initial testing of an installation -Have differ slightly from one country to another: The principles are common, and are based on the observance of rigorous safety rules in the design and realization of the installation. -The pre-commissioning electrical tests and visual-inspection checks for installations : + Insulation tests of all cable and wiring conductors of the fixed installation, between phases and between phases and earth. +Continuity and conductivity tests of protective, equipotential and earth-bonding conductors. +Resistance tests of earthing electrodes with respect to remote earth. +Check of allowable number of socket-outlets per circuit…etc. Periodic check-testing of an installation Periodic check-testing of an installation -In many countries, all industrial and commercial-building installations, together with installations in buildings used for public gatherings, must be re-tested periodically by authorized agents. Figure below shows the frequency of testing commonly prescribed according to the kind of installation concerned. Environment Environment -A product environmental design sometimes called “eco-design” is an approach of sustainable development with the objective of designing products/services best meeting the customers’ requirements while reducing their environmental impact over their whole life cycle. -The methodologies used for this purpose lead to choose equipment’s architecture together with components and marterials taking into account the influence of a product on the environment along its life cycle (from extraction of raw materials to scrap) i.e. production, transport, distribution, end of life …etc. Environment -In Europe two Directives have been published, they are called: + RoHS Directive (Restriction of Hazardous Substances) aims to eliminate from products six hazardous substances: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated biphenyl ethers (PBDE). +WEEE Directive (Waste of Electrical and Electronic Equipment) in order to master the end of life and treatments for household and non household equipment. Summary and Conclusion Summary and Conclusion Summary : -Rules and standards of electrical installation design - -About “environment” when produce equipment in general and electric equipment in particular. Conclusion : -Above issue principles and requirement when electrical installation design. Suggestion: -Every body have to correct insight with anything. . DIVISION OF INDUSTRIAL ELECTRICSITY DIVISION OF INDUSTRIAL ELECTRICSITY Subject : General rules of electrical installation design Subject : General rules of electrical. safety of an electrical installation +Initial testing of an installation +Periodic check-testing of an installation +Environment Definition of voltage ranges

Ngày đăng: 02/08/2013, 01:25

Từ khóa liên quan

Tài liệu cùng người dùng

  • Đang cập nhật ...

Tài liệu liên quan