Đang tải... (xem toàn văn)
The main purpose of this study is to assess forest fire susceptibility maps (FFSMs) and their performances comparison using modified analytical hierarchy process (MAHP) and Mamdani fuzzy logic (MFL) models in a geographic information system (GIS) environment. This study was carried out in the Minudasht Forests, Golestan Province, Iran, and was conducted in three main stages such as spatial data construction, forest fire modelling using MAHP and MFL, and validation of constructed models using receiver operating characteristic (ROC) curve. At first, seven conditioning factors, such as altitude, slope aspect, slope angle, annual temperature, wind effect, land use, and normalized different vegetation index, were extracted from the spatial database. In the next step, FFSMs were prepared using MAHP and MFL modules in a NetcadGIS Architect environment. Finally, the ROC curves and area under the curves (AUCs) were estimated for validation purposes. The results showed that the AUCs for MFL and MAHP are 88.20% and 77.72%, respectively. The results obtained in this study also showed that the MFL model performed better than the MAHP model. These FFSMs can be applied for land use planning, management, and prevention of future fire hazards.
Geomatics, Natural Hazards and Risk ISSN: 1947-5705 (Print) 1947-5713 (Online) Journal homepage: http://www.tandfonline.com/loi/tgnh20 A comparative assessment of prediction capabilities of modified analytical hierarchy process (M-AHP) and Mamdani fuzzy logic models using Netcad-GIS for forest fire susceptibility mapping Hamid reza Pourghasemi, Masood Beheshtirad & Biswajeet Pradhan To cite this article: Hamid reza Pourghasemi, Masood Beheshtirad & Biswajeet Pradhan (2016) A comparative assessment of prediction capabilities of modified analytical hierarchy process (M-AHP) and Mamdani fuzzy logic models using Netcad-GIS for forest fire susceptibility mapping, Geomatics, Natural Hazards and Risk, 7:2, 861-885, DOI: 10.1080/19475705.2014.984247 To link to this article: http://dx.doi.org/10.1080/19475705.2014.984247 © 2014 Taylor & Francis Published online: 01 Dec 2014 Submit your article to this journal Article views: 142 View related articles View Crossmark data Full Terms & Conditions of access and use can be found at http://www.tandfonline.com/action/journalInformation?journalCode=tgnh20 Download by: [203.128.244.130] Date: 15 March 2016, At: 00:53 Geomatics, Natural Hazards and Risk, 2016 Vol 7, No 2, 861À885, http://dx.doi.org/10.1080/19475705.2014.984247 Downloaded by [203.128.244.130] at 00:53 15 March 2016 A comparative assessment of prediction capabilities of modified analytical hierarchy process (M-AHP) and Mamdani fuzzy logic models using Netcad-GIS for forest fire susceptibility mapping HAMID REZA POURGHASEMIy*, MASOOD BEHESHTIRADz and BISWAJEET PRADHAN x yDepartment of Natural Resources and Environment, College of Agriculture, Shiraz University, Shiraz, Iran zDepartment of Natural Resources, Sirjan Branch, Islamic Azad University, Sirjan, Iran xDepartment of Civil Engineering, Faculty of Engineering, Geospatial Information Science Research Center (GISRC), University Putra Malaysia, Serdang 43400, Malaysia (Received 31 May 2014; accepted November 2014) The main purpose of this study is to assess forest fire susceptibility maps (FFSMs) and their performances comparison using modified analytical hierarchy process (M-AHP) and Mamdani fuzzy logic (MFL) models in a geographic information system (GIS) environment This study was carried out in the Minudasht Forests, Golestan Province, Iran, and was conducted in three main stages such as spatial data construction, forest fire modelling using M-AHP and MFL, and validation of constructed models using receiver operating characteristic (ROC) curve At first, seven conditioning factors, such as altitude, slope aspect, slope angle, annual temperature, wind effect, land use, and normalized different vegetation index, were extracted from the spatial database In the next step, FFSMs were prepared using M-AHP and MFL modules in a Netcad-GIS Architect environment Finally, the ROC curves and area under the curves (AUCs) were estimated for validation purposes The results showed that the AUCs for MFL and M-AHP are 88.20% and 77.72%, respectively The results obtained in this study also showed that the MFL model performed better than the M-AHP model These FFSMs can be applied for land use planning, management, and prevention of future fire hazards Introduction Forests are major natural resources which play a crucial role in maintaining environmental balance The health of forest in a given area is a true indicator of the ecological condition prevailing in that area (Saklani 2008) In general, fire is a natural component of many forest ecosystems and cannot be avoided (Dimopoulou & Giannikos 2001) Forest fires cause major damages to environment, human health and property, and endanger life (Rawat 2003) Six million square kilometre of forests has been lost around the world in less than 200 years mainly due to forest fire (Dimopoulou & Giannikos 2002) In Iran, forest fire is one of the most natural occurring hazards According to the ECE/FAO database (Economic Commission for Europe/ Food and Agriculture Organization) on forest fires in 1982À1995, the number of *Corresponding author Email: hamidreza.pourghasemi@yahoo.com Ó 2014 Taylor & Francis Downloaded by [203.128.244.130] at 00:53 15 March 2016 862 H.R Pourghasemi et al forest fires per year is 130 and the burnt average area and its maximum is 54 km2 and 330 km2, respectively (Allard 2001) During the period 1991À1997, nearly 3063 fires have been reported, of which 13,700 was burnt In the year 1998, there were 998 fires reported and the burnt area was estimated at 206,713 covering mostly shrubs Losses were estimated at more than 5.6 million Rials (almost USD 3200 in the year of 1998), including 8761 tons of cattle feed lost (Allard 2001) In a recent paper, Janbaz Ghobadi et al (2012) reported that, in the last decade, 9086 of the forests have been affected by forest fire Also, in Iran, it is difficult to control forest fire naturally; however, it is possible to map different hazard levels for minimizing fire hazards and avoid potential damage In the literature, several different methods and techniques for forest fire susceptibility and risk mapping have been proposed and tested Many studies have evaluated forest fire using geographic information system (GIS) and remote sensing (RS) technologies (Chuvieco & Congalton 1989; Prosper-Laget et al 1995; Castro & Chuvieco 1998; Jaiswal et al 2002; Erten et al 2004; Wulder & Franklin 2006; Pradhan et al 2007; Razali 2007; Saklani 2008; Chuvieco et al 2010; Pradhan & Assilzadeh 2010; Adab et al 2013; Teodoro & Duarte 2013) Several studies have applied probabilistic-based models such as fuel moisture content (FMC), fire area simulator (FARSITE), and Maxent models (Chuvieco et al 2004; Garcıa et al 2008; Krasnow et al 2009; Renard et al 2012) In the past decade, some methods, such as artificial neural networks (ANNs) (Betanzos et al 2002; Maeda et al 2009; Bisquert et al 2012; Safi & Bouroumi 2013), fuzzy logic (Nadeau et al 2005; Carvalho et al 2006; Agarwal et al 2013), and adaptive neuro-fuzzy inference system (ANFIS) (Angayarkkani & Radhakrishnan 2011), have been proposed Recently, new forest risk assessment methods, such as support vector machine (SVM) (Cortez & Morais 2007; Koetz et al 2008; Zhao et al 2011), decision tree methods (Stojanova et al 2006), and random forest (Cortez & Morais 2007; Pierce et al 2012; Leuenberger et al 2013), were employed and their performances were assessed The aim of the current research is to assess forest fire susceptibility maps (FFSMs) using modified analytical hierarchy process (M-AHP) and Mamdani fuzzy logic (MFL) models developed in Netcad GIS The assessment was performed in the Minudasht forests situated in Golestan Province, Iran The main difference between this research and the approaches described in the aforementioned publications is that an M-AHP model is applied and the result is compared with MFL model in the study area Also, expert opinions are used in the mentioned models for defining the rules and conditioning factor scores in MFL and M-AHP models, respectively This contribution provides originality to this study Study area The study area is located in the eastern part of Golestan Province, in the north of Iran, between latitudes 37 000 2700 to 37 270 5300 N, and longitudes 55 140 0000 to 56 000 3900 E (figure 1) It covers an area about 1531 km2 This county shares boundaries with other Golestan Province counties such as Kalaleh county in the north and Azadshahr county in the west (Shadman Roodposhti et al 2014) The elevation of the study area ranges between 100 and 2500 m above the mean sea level The climate of Minudasht ranges between temperate and semi-humid types The mean annual Downloaded by [203.128.244.130] at 00:53 15 March 2016 Geomatics, Natural Hazards and Risk 863 Figure Forest fire location (black and pink dots) map in the study area Modified from Pourtaghi et al (2014) To view this figure in colour, please see the online version of the journal precipitation within the study area varies from 138 to 335 mm (Shadman Roodposhti et al 2014) Based on Iranian Meteorological Organization, maximum and minimum of temperature were reported as C40 and ¡5 C, respectively Agriculture is the main economic activity of the region In addition, part of the Golestan National Park is located within the county and it is known as tropical dry forests Methodology The overall methodology flow chart of the study is shown in figure The flowchart consists of three phases: (1) data integration and analysis, (2) forest fire susceptibility modelling using M-AHP and MFL approaches, and (3) validation of the constructed models using receiver operating characteristic (ROC) curve 3.1 Data integration and analysis In general, data collection and construction of a database of effective factors in any study area are the most important parts of the process (Ercanoglu & Gokceoglu 2002) At first, fire occurrences and locations were collected from MODIS (Moderate-Resolution Imaging Spectro Radiometer) satellite images (collected in year Downloaded by [203.128.244.130] at 00:53 15 March 2016 864 H.R Pourghasemi et al Figure Flow chart of used methodology in the study area 2010), extensive field surveys, and national reports Forest fires are related to year 2010, at 1:25,000 scale (table 1) Out of 151 forest fire locations, 70% were used in the model training and the remaining 30% were used for validation (Pourghasemi et al 2012a; Zare et al 2012; Pourghasemi et al 2014; Regmi et al 2014) For FFSM in the study area, seven effective factors were considered These factors include altitude, slope aspect, slope angle, annual temperature, wind effect, land use, and normalized different vegetation index (NDVI) The spatial database for the study area is shown in table Table Data used for forest fire susceptibility mapping (FFSM) Data layers Data format Forest fire locations map Point Topographic map Line and point Land use Polygon Normalized difference vegetation index (NDVI) Meteorological data Grid Excel data Source of data Satellite image, aerial photos, and extensive field surveys National Cartographic Center (NCC) National Geographic Organization (NGO) National Geographic Organization (NGO) Iranian Meteorological Organization (IRIMO) Scale 1:25,000 1:50,000 1:100,000 30m £ 30m À Downloaded by [203.128.244.130] at 00:53 15 March 2016 Geomatics, Natural Hazards and Risk 865 One of the important factors in any fire hazard rating system is topography data In the literatures, the impacts of elevation, slope aspect, and slope angle in fire behaviour have been widely reported (Chuvieco & Congalton 1989; Erten et al 2004; Renard et al 2012; Adab et al 2013) In the current research, a digital elevation model (DEM) was created by digitizing contours (30 m interval) and survey base points The DEM map has a grid size of 30 m with 2323 columns and 1657 rows Using the DEM, altitude, slope aspect, and slope angle were extracted (figures 3(a) and (b)) Elevation is a crucial physiographic variable that is associated with temperature, moisture, and wind (Xiangwei et al 2011) Therefore, it has an important role in fire spreading (Jaiswal et al 2002) The altitude map was extracted from the DEM and classified into five classes according to equal interval classification (Pradhan et al 2007; Pourtaghi et al 2014); that is, (1) 2000 m (figure 3(a)) Slope aspect is another factor that correlated with the amount of received solar energy in the area Therefore, slope aspect layer was selected as one of the forest fire-related factors and has been categorized into nine classes: (1) flat, (2) north, (3) north-east, (4) east, (5) south-east, (6) south, (7) south-west, (8) west, and (9) north-west (figure 3(b)) Also, one of the parameters that influence the fire spread rate is slope angle (Weise & Biging 1997) Fire can move more quickly up the slope and less quickly down the slope (Kushla & Ripple 1997) So, the slope map of the study area is derived from the DEM and divided into four classes such as 0 À5 , 5 À15 , 15 À30 , and >30 (figure 3(c)) In addition, using the meteorological database, the annual temperature and wind effect factors were calculated (figures 4(a) and (b)) Temperature highly affects the moisture amount in forest combustion High temperature led to dry combustion quickly (Antoninetti et al 1993) The annual temperature map was classified as follows: 18 C (figure 4(a)) Wind is an important factor because it provides fresh oxygen and the flame puts a new fuel source (Rawat 2003) Wind effect factor map was created based on three input parameters, such as DEM in grid format, wind direction (degree), and wind speed (m/s) in SAGA GIS (http://saga.sourcearchive.com/documentation/2.0.7pluspdfsg-2/wind effect_8cpp_source.html) In the current research, the wind effect was prepared in SAGA-GIS and classified based on the natural break classification scheme (Pourtaghi et al 2014) into three classes such as (0.75À0.95), (0.95À1.14), and (>1.14) (figure 4(b)) The land use map was created using Landsat-7 images of 2010 In order to create the land use map, a supervised classification using maximum likelihood algorithm was applied A total of 370 signatures (training classes) were collected from all land use types The signatures were collected by field survey and using GPS Out of these 370 signatures, 250 signatures were used for land use mapping and the remaining were used for accuracy assessment Nine land use classes were drawn such as irrigation farming (IF), dense forest (DF), sparse forest (SF), irrigated and rain-fed mixed farming (IRMF), rain-fed farming (RF), good range (GR), moderate range (MR), moderate forest (MF), woodlands and shrubbery (WS), and urban (residential) (U) (figure 5) For assessment of vegetation cover, we used normalized difference vegetation index (NDVI), which is the most commonly used index to assess live FMC (Chuvieco H.R Pourghasemi et al Downloaded by [203.128.244.130] at 00:53 15 March 2016 866 Figure Topographical parameter maps of the study area: (a) altitude, (b) slope aspect and (c) slope angle Modified from Pourtaghi et al (2014) Downloaded by [203.128.244.130] at 00:53 15 March 2016 Geomatics, Natural Hazards and Risk 867 Figure (Continued) 2003) The NDVI was prepared using Landsat-7 images (path 162 and row 34 obtained on 13 November 2010) based on the following equation (Rouse et al 1973): NDVI ¼ NIR ¡ RED ; NIR ỵ RED (1) where NIR (band 4) and RED (band 3) values are the infrared and red portion of the electromagnetic spectrum, respectively In this study, the NDVI map was prepared in ENVI 4.8 and divided into six classes (figure 6) For classification of conditioning factors, different methods were used such as equal interval, natural break, and normal or common standards Finally, for application of M-AHP and MFL models, all the aforementioned conditioning factors were converted to a raster grid with 30 m £ 30 m pixel size in the ArcGIS 9.3 software All the maps are in UTM (Universal Transvers Mercator) coordinate system and WGS84 spatial reference (WGS84-UTM-Zone40N) 3.2 Statistical index In this research, the statistical index (SI) model was applied to illustrate the quantitative relationship between distributions of forest fire occurrences with predictor factors The SI method is a bivariate statistical analysis proposed by van Westen (1997) A weight value for each categorical unit is defined as the natural logarithm of the H.R Pourghasemi et al Downloaded by [203.128.244.130] at 00:53 15 March 2016 868 Figure Meteorological parameter maps of the study area: (a) annual temperature and (b) wind effect (no dimension) Modified from Pourtaghi et al (2014) Downloaded by [203.128.244.130] at 00:53 15 March 2016 Geomatics, Natural Hazards and Risk 869 Figure Land use map of the study area Modified from Pourtaghi et al (2014) forest fire density in the categorical unit divided by the forest fire density in the entire map (van Westen 1997; Rautela & Lakhera 2000; Cevik & Topal 2003; Pourghasemi, Moradi, et al 2013) This method is based on the following equation (van Westen 1997): WSI ¼ ln Fij =FT ; Pij =PT (2) where WSI is the weight given to a certain class i of parameter j; Fij is the number of forest fires in a certain class i of parameter j; FT is the total number of forest fires in the entire map; Pij is the number of pixels in a certain class i of parameter j; and PT is the total pixels of the entire map 3.3 Modified analytical hierarchy process The analytical hierarchy process (AHP) is a theory of measurement for considering tangible and intangible criteria that have been applied to numerous areas, such as decision theory and conflict resolution (Vargas 1990; Yalcin 2008; Youssef et al 2011) The AHP includes a matrix-based pairwise comparison of the contribution of different factors on forest fire occurrence The process consists of four phases: Geomatics, Natural Hazards and Risk 871 Table The AHP pairwise comparison scale (Saaty 1994) Numerical values Downloaded by [203.128.244.130] at 00:53 15 March 2016 2, 4, 6, and Verbal scale Equal importance of both elements Moderate importance of one element over another Strong importance of one element over another Very strong importance of one element over another Extreme importance of one element over another Intermediate values Explanation Two elements contribute equally Experience and judgment favour one element over another An element is strongly favoured An element is very strongly dominant An element is favoured by at least an order of magnitude Used to compromise between two judgments (1) The preparation of the factor comparison matrix In this step, there are following differences: The factor comparison matrix in the M-AHP model is not according to the expert opinion, The expert viewpoints in M-AHP only used to define the maximum scores for each factor in order to prepare factor score matrix, Normalization of the factor score values according to maximum score factor, Finally, construction of factor comparison matrix based on modified importance value scale (Nefeslioglu et al 2013) (2) The evaluation of the importance distributions of the conditioning factors on the decision points (Nefeslioglu et al 2013) In this step, at first, each factor will be normalized based on its own maximum score Subsequently, linear distance between the normalized factor score and decision points will be calculated, and finally decision point comparison matrix will be prepared by considering modified importance value scale In other words, it is sufficient for the expert to identify important factors at model running (http://portal.netcad.com.tr/pages/viewpage.action?pageIdD113803523) The details of the mentioned algorithm/tool (M-AHP) with an example on snow avalanche can be found in Nefeslioglu et al (2013) 3.4 Mamdani fuzzy logic The fuzzy set theory was first introduced by Zadeh (1965), and it is one of the tools used to handle complex problems Fuzzy sets theory is a mathematical method used to characterize and propagate uncertainty and imprecision in data and functional relationships (Kurtener & Badenko 2000) The mentioned theory has been commonly used in different scientific studies and disciplines (Juang et al 1992; Alvarez Grima & Babuska 1999; Ercanoglu & Gokceoglu 2002; Nefeslioglu et al 2006; Saboya et al 2006; Gokceoglu et al 2009; Yagiz & Gokceoglu 2010; Akgun et al 2012; Pourghasemi et al 2012b; Osna et al 2014) In the fuzzy set theory, 872 H.R Pourghasemi et al Downloaded by [203.128.244.130] at 00:53 15 March 2016 membership can take on any value between and 1, reflecting the degree of certainty of membership (Zadeh 1965; Pradhan 2011) A membership value was chosen arbitrary according to subjective judgement about the relative importance of the maps and their various states (Bonham-Carter 1994) A number of different types of membership functions (MFs) have been proposed for fuzzy inference system These MFs are triangular, trapezoidal, sigmoidal, bell, Gaussian combination, and p-shaped (Pradhan 2013; Osna et al 2014) Meanwhile, in the literature, different fuzzy inference systems (FIS) have been proposed (Mamdani, Sugeno, and Tsukamoto), but the Mamdani fuzzy is one of the most interesting methods applied in engineering geology problems (Alvarez Grima 2000; Akgun et al 2012) In the Mamdani fuzzy model, ifÀthen rules replace the usual set of equations used to characterize a system (Yager & Filev 1994) The Mamdani fuzzy model takes the following form: Ri : if x1 is Ai1 and xj is Aij ; then y is Bi for i ¼ 1; 2; :::; k and j ¼ 1; 2; :::; r; (3) where k is the number of rules, xj ðj ¼ 1; 2; ; rÞ are input variables, y is the output variables, and Aij and Bi are linguistic terms In Mamdani model, each rule is a fuzzy relation Ri X ÊY ! ẵ0; 1ị which is calculated using the following equation: mRi x; yị ẳ ImAi xị; mBi yịị; (4) where the operator I can be either a fuzzy implication or a conjunction operator (tnorm) (Jager 1995) There are four inference steps in Mamdani fuzzy inference system such as fuzzification, rule assessment, aggregation, and defuzzification steps (Mamdani & Assilian 1975); they are presented in equations (5)À(7) Step 1: compute the degree of fulfillment of the antecedent for each rule i: ẳ mAi1 x1 ị ^ mAi2 x2 Þ ^ ::: ^ mAin ðxn Þ:::1 i k: (5) Step 2: for each rule, drive the output fuzzy set Bi using the minimum t-norm: mB0 ðyÞ ¼ ^ mBi ðyÞ: i (6) Step 3: Aggregate the output fuzzy sets by taking the maximum method (Eq 8): mB ¼ maxm i D 1;2;:::;k : ¡iðyÞ B (7) Finally, in this study, due to defuzzification process (Step 4) was used of the centroid method because of its simplicity and producing consistent results (Jager 1995) The details of the mentioned algorithm can be found in Alvarez Grima (2000) Geomatics, Natural Hazards and Risk 873 As a result, the fuzzy logic allows more flexible combinations of weighted maps and could be readily implemented in GIS modelling language (Pradhan 2010a, 2010b) For applying of the mentioned models (M-AHP and MFL) were used of a laptop computer by a hardware configuration such as CORE i7 processor, 64-bit CPU and 6GB RAM, the inference process completes in approximately hours But the computer output in the M-AHP model can be obtained in a less time, almost at 10 Results Downloaded by [203.128.244.130] at 00:53 15 March 2016 4.1 Statistical index (SI) The spatial relationship between forest fire occurrences and the conditioning factors using the SI model is presented in table According to the relationship between forest fire occurrence and altitude, forest fire numbers or frequency is highest at elevations higher than 500 m Thus, the probability of occurrence of fire in these altitudes is higher Chuvieco and Congalton (1989) and Adab et al (2013) reported that fire behaviour trends are less severe at higher altitudes because of higher rainfall The SI value between forest fire occurrence and slope aspect shows that forest fires are most common on east (SI D 0.89), south-west (SI D 0.38), and west (SI D 0.21) facing slopes, respectively, and the flat (SI D ¡0.5) and north-west (SI D ¡0.36) facing slopes have the lowest incidence The analysis of SI for the relationship between forest fire occurrence and slope degree indicates that slope degree class >30 and 1.14 is considered to be susceptible to fire with an SI value of 0.47 In the case of land use, it can be inferred that 99.06% of forest fire falls on dense forest area with value of 0.51, indicating that the probability of occurrence of forest fire in this land use type is very high The NDVI factor indicates that the range between 0.1 and 0.5 and >0.5 have the highest frequency for forest fire occurrence (26.42% and 72.64%) On the other hand, the remaining classes are lowest susceptible or nonsusceptible to forest fire occurrence 4.2 Forest fire susceptibility mapping (FFSM) by M-AHP model For FFSM, a tool was developed in Netcad GIS as M-AHP At first, seven forest fire conditioning factors were classified based on literature review and expert knowledge Then, the score of their classes (condition factor classes) was determined according to expert knowledge (table 4) and, subsequently, maximum score factors were extracted In the mentioned table, for the altitude, the maximum score is for classes >2000 m Hernandez-Leal et al (2006) reported that humidity and temperature have higher influence on fire at higher altitude areas than lower ones In the case of slope aspect, maximum scores referred to south-facing slopes by value of It is noticed that south-facing slopes received more sunlight, higher temperatures, stronger winds, low humidity, and low fuel moistures than those facing the north pole Thus, vegetation is generally drier and less dense on south-facing slopes than northfacing ones (Anderson 1982; Prasad et al 2008), and drier fuels are more prone to 874 H.R Pourghasemi et al Table Spatial relationship between conditioning factors and forest fire locations using statistical index (SI) model Factor Altitude (m) Downloaded by [203.128.244.130] at 00:53 15 March 2016 Slope aspect Slope angle (degree) Annual temperature (mm) Wind effect Land useà NDVI Class No of pixels in domain (Pij) % Pixels in domain No of forest fires (FFij) % forest fires SI 30 18 0.75À0.95 0.95À1.14 >1.14 2 3 7 IR DF LF IRMF RF GR MF WS U IR 0.5 1 1 1 1 1 7 5 Downloaded by [203.128.244.130] at 00:53 15 March 2016 876 H.R Pourghasemi et al ignition (Noonan 2003; Iwan et al 2004) For the slope degree, the maximum score is for slopes >30 Kushla and Ripple (1997) stated that fire can move more quickly up the slope and less quickly down the slope On the other hand, flames being angled closer to the ground surface, thus, fire spread rate may rise on steeper slopes, and the process of heat convection can be enhanced by wind effects due to fire behaviour (Whelan 1995; DeBano et al 1998; Adab et al 2013) The maximum score for annual temperature showed that higher temperature caused dry combustion (Artsybashev 1983; Antoninetti et al 1993) and the resulting classes >18 C have the highest maximum value (score D 7) In the case of wind effect and according to the expert knowledge scores, when wind effect increases, the probability of forest fire increases In other words, the rate of burning is increased with increasing of wind effect (Rawat 2003) So, classes of >1.14 have a highest score (score D 5) Another important factor for forest fire occurrence is land use type The relationships between forest fire locations and land use types show that 99.06% of forest fire falls on dense forest area with value of 0.51, indicating that the probability of occurrence of forest fire in this land use type is very high Thus, for M-AHP model, the maximum score (score D 5) corresponded to dense forest land use type In the case of NDVI, maximum score was In the range of greater than 0.5, the study area is generally covered by dense vegetation and tropical rainforest, so it is susceptible to fire occurrence Another important problem in calculation of M-AHP is instant factor scores During application of the model, for any terrain mapping unit in the field, instant factor scores should also be defined by the expert or relevant user (Nefeslioglu et al 2013) But, one of the attributes of Netcad GIS is that the instant scores will be obtained from the region basin (study area basin) automatically In other words, they are computed from the raster maps used in this study For running the M-AHP model, one key point is determination of decision points In the current research, the decision points for the FFSM is grouped into four classes as low, moderate, high, and very high (figure 7(a)) Finally, the FFSM prepared from the M-AHP method, which covered 29.66% of the total area, was designated to be a low FFSM class; 20.78, 33.17, and 16.39% of the total area are related to moderate, high, and very high FFSM zones, respectively (figure 7(a)) 4.3 Forest fire susceptibility mapping (FFSM) by Mamdani fuzzy logic To produce FFSM using Mamdani fuzzy inference system (FIS), at first, conditioning factors were created in raster format with a 30 m £ 30 m pixel size in GIS environment After the inputs were loaded to Netcad GIS 6, the user can select a fuzzy existing model or build a new one based on the input numbers in the Architect page In the next step, membership functions were defined for input and output layers The input layers are the same as considered in the previous models Due to definition of membership function for categorical factors such as slope aspect and land use, the forest fire density and spatial relationship between these factors and forest fire locations (table 1) were considered in the current research To minimize the uncertainty, a 50% overlap is applied between the fuzzy sets for each input parameter, and triangular membership functions are used for each fuzzy set (Akgun et al 2012) On the other hand, output set as FFSM and its membership function draw into four classes such as low, moderate, high, and very high Another 877 Downloaded by [203.128.244.130] at 00:53 15 March 2016 Geomatics, Natural Hazards and Risk Figure Forest fire susceptibility map (FFSM) produced by M-AHP (a) and MFL (b) models Modified from Pourtaghi et al (2014) H.R Pourghasemi et al Downloaded by [203.128.244.130] at 00:53 15 March 2016 878 Figure Prediction rate curve for the forest fire susceptibility map by MFL (a) and M-AHP (b) models Geomatics, Natural Hazards and Risk 879 important part in Mamdani FIS is definition of the fuzzy ifÀthen rules In this study, a total 128 ifÀthen rules were used First, the ifÀthen rules are created automatically and then edited according to expert opinion For transforming output linguistic variables into crisp values, defuzzification method should be used Thus, for FFSM, the most common defuzzification method, namely, gravity center, was used (Jager 1995; Babuska 1996; Saboya et al 2006) Finally, the FFSM produced from the MFL method, which covered 23.17% of the total area, was designated to be a low FFSM class; 24.41, 38.97, and 13.45% of the total area are related to moderate, high, and very high FFSM zones, respectively (figure 7(b)) Downloaded by [203.128.244.130] at 00:53 15 March 2016 4.4 Validation of forest fire susceptibility maps In general, the validation of predicted results is the crucial step in the modelling process, so that the results can provide a meaningful interpretation (Fabbri & Chung 2001; Chung & Fabbri 2003) To determine the accuracy of the two FFSMs produced using M-AHP and MFL models, the ROC curve (Pradhan et al 2009; Pradhan 2010a, 2010b, 2011; Akgun et al 2012; Mohammady et al 2012; Pourghasemi, Goli Jirandeh, et al 2013; Osna et al 2014; Jaafari et al 2014) was used ROC curve analysis is a common method used to assess the diagnostic test accuracy (Egan 1975) The ROC curve plots the true positive rate on the Y-axis and the false positive rate on the X-axis It represents the trade-off between the two rates (Negnevitsky 2002) In the ROC method, the area under the curve (AUC) values range from 0.5 to 1.0 and are used to evaluate the model accuracy (Nandi & Shakoor 2010) If the model does not predict the forest fire occurrences better than the chance, the AUC would equal 0.5 A ROC curve of shows perfect prediction (Yesilnacar 2005) The quantitativeÀqualitative relationship between AUC and prediction accuracy can be classified as follows: 0.9À1, excellent; 0.8À0.9, very good; 0.7À0.8, good; 0.6À0.7, average; and 0.5À0.6, poor (Yesilnacar 2005) In this study, the forest fire locations that were not used during the model building process were used to verify the FFSMs The AUC values of the ROC curve for MFL and M-AHP models were found to be 88.20% and 77.72% with a standard error of 0.042 and 0.49, respectively (figures (a) and (b)) Hence, it is concluded that the MFL model employed in this study showed more reasonable results with respect to the M-AHP model in predicting the forest fire susceptibility of study area Conclusion The present study attempts to assess FFSMs produced by the M-AHP and MFL models and to compare their performances The results of this study suggest that FFSMs for the Minudasht Township, Golestan Province, of Iran are viable Meanwhile, based on the obtained AUC, the MFL model has better prediction performance (88.20%) than the M-AHP (77.72%) model As a result, the FFSM by MAHP is easy, because the mentioned model does not use the membership functions and ifÀthen fuzzy rules; thus, it takes a less time for model running According to Nefeslioglu et al (2013), another advantage of the M-AHP is that, using this methodology, the consistency ratio value for the comparison matrix and the weights never exceeds 0.10 In contrast, fuzzy algorithm is a powerful tool in modelling of complex 880 H.R Pourghasemi et al natural processes and nonlinear systems Finally, these maps can be used to early warning, fire suppression resources planning, and allocation works Acknowledgements The authors would like to thank Prof Candan Gokceoglu, Dr Hakan A Nefeslioglu, Turgay Osna, and Deniz Celik for their supports in creating and training of spatial analyst in the Netcad GIS 6, especially on M-AHP and MFL modules Also, the authors would like to thank the three anonymous reviewers for their helpful comments on the previous version of the manuscript ORCID Downloaded by [203.128.244.130] at 00:53 15 March 2016 Biswajeet Pradhan http://orcid.org/0000-0001-9863-2054 References Abba AH, Noor ZZ, Yusuf RO, Mohd Din MF, Abu Hassan MA 2013 Assessing environmental impacts of municipal solid waste of Johor by analytical hierarchy process Resour Conserv Recycl 73:188À196 Adab H, Devi Kanniah K, Solaimani K 2013 Modeling forest fire risk in the northeast of Iran using remote sensing and GIS techniques Nat Hazards 65:1723À1743 Agarwal PK, Patil PK, Mehal R 2013 A methodology for ranking road safety hazardous locations using analytical hierarchy process Proc Soc Behav Sci 104: 1030À1037 Akgun A, Sezer EA, Nefeslioglu HA, Gokceoglu C, Pradhan B 2012 An easy-to-use MATLAB program (MamLand) for the assessment of landslide susceptibility using a Mamdani fuzzy algorithm Comput Geosci 38:23À34 Allard G 2001 The fire situation in Islamic Republic of Iran Global forest fire assessment 1990-2000 Working Paper 55, Rome p 198À202 http://www.fao.org/forestry/en/ Alvarez Grima M 2000 Neuro-fuzzy modeling in engineering geology Rotterdam: Balkema Alvarez Grima M, Babuska R 1999 Fuzzy model for the prediction of unconfined compressive strength of rock samples Int J Rock Mech Mining Sci 36:339À349 Anderson HE 1982 Aids to determining fuel models for estimating fire behavior Intermountain Forest and Range Experiment Station General Technical Report INT-122 Ogden (UT): USDA Forest Service Angayarkkani K, Radhakrishnan N 2011 An effective technique to detect forest fire region through ANFIS with spatial data 3rd International Conference on Electronics Computer Technology (ICECT); 2011; Kanyakumari, India; p 24À30 doi:10.1109/ ICECTECH.2011.5941794 Antoninetti M, Binagli E, Rampini A, D’Angelo M 1993 The integrated use of satellite and topographic data for forest fire hazard map In: Winkler P, Balkema AA, editors Remote sensing for monitoring the changing environment of Europe Rotterdam: Brookfield; p 179À184 Artsybashev ES 1983 Forest fires and their control lst ed New Delhi: Oxonian (in Russian, 1974) Ayalew L, Yamagishi H, Marui H, Kanno T 2005 Landslides in Sado Island of Japan Part II GIS-based susceptibility mapping with comparisons of results from two methods and verifications Eng Geol 81:432À445 Babuska R 1996 Fuzzy modelling and identification [dissertation] Delft: Delft University of Technology Betanzos AA, Fontenla-Romero O, Guijarro-Berdinas B, Hernandez-Pereira E, Canda J, Jimenez E, Legido JL, Muniz S, Paz-Andrade C, Paz-Andrade MI 2002 A neural Downloaded by [203.128.244.130] at 00:53 15 March 2016 Geomatics, Natural Hazards and Risk 881 network approach for forestal fire risk estimation In: Van Harmelen F, editor Proceedings of the 15th Eureopean Conference on Artificial Intelligence, ECAI’2002; 2002 July; Lyon, France p 643À647 Bisquert M, Caselles E, Sanchez E, Caselles V 2012 Application of artificial neural networks and logistic regression to the prediction of forest fire danger in Galicia using MODIS data J Wildland Fire 1:1025À1029 Bonham-Carter GF 1994 Computer methods in the geosciences Vol 13 Ontario: Pergamon Carvalho JP, Carola M, Tome JAB 2006 Forest fire modeling using rule-based fuzzy Cognitive maps and Voronoi based cellular automata Annual meeting of the North American Fuzzy Information Processing Society NAFIPS 2006; 2006 Jun 3À6; Quebec, Canada; p 217À222 Castro R, Chuvieco E 1989 Modeling forest fire danger from geographic information systems Geocarto Int 13:15À23 Cevik E, Topal T 2003 GIS-based landslide susceptibility mapping for a problematic segment of the natural gas pipeline, Hendek (Turkey) Environ Geol 44:949À962 Chung CF, Fabbri AG 2003 Validation of spatial prediction models for landslide hazard mapping Nat Hazards 30:451À472 Chuvieco E 2003 Wildland fire danger estimation and mapping: the role of remote sensing data Series in remote sensing Vol Singapore: World Scientific Chuvieco E, Aguadoa I, Yebraa M 2010 Development of a framework for fire risk assessment using remote sensing and geographic information system technologies Ecol Model 221:46À58 Chuvieco E, Coceroa D, Riano D, Martinc P, Martıiez-Vega J, de la Riva J, Perez F 2004 Combining NDVI and surface temperature for the estimation of live fuel moisture content in forest fire danger rating Remote Sens Environ 92:322À331 Chuvieco E, Congalton RG 1989 Application of remote sensing and geographic information systems to forest fire hazard mapping Remote Sens Environ 29:147À159 Cortez P, Morais A 2007 A data mining approach to predict forest fires using meteorological data In: Neves J, Santos MF, Machado J, editors New Trends in Artificial Intelligence Proceedings of the EPIA 2007 À Portuguese Conference on Artificial Intelligence; 2007 December; Guimar~aes, Portugal, p 512À523 DeBano LF, Neary DG, Ffolliott PF 1998 Fire’s effects on ecosystems New York (NY): Wiley Dimopoulou M, Giannikos I 2001 Spatial optimization of resources deployment for forestfire management Int Trans Oper Res 8:523À534 Dimopoulou M, Giannikos I 2002 Towards an integrated framework for forest fire control Eur J Oper Res 152:476À486 Egan JP 1975 Signal detection theory and ROC analysis Vol 195 New York (NY): Academic Press; p 266À268 Ercanoglu M, Gokceoglu C 2002 Assessment of landslide susceptibility for a landslide-prone area (North of Yenice, NW Turkey) by fuzzy approach Environ Geol 41:720À730 Erten E, Kurgun V, Musaoglu N 2004 Forest fire risk zone mapping from satellite imagery and GIS: a case study XXth Congress of the International Society for Photogrammetry and Remote Sensing, Istanbul, Turkey; p 222À230 Esmali Ouri A, Amirian S 2009 Landslide hazard zonation using MR and AHP methods and GIS techniques in Langan watershed, Ardabil, Iran International Conference on ACRS 2009; Beijing, China Fabbri AG, Chung CF 2001 Spatial support in landslide hazard prediction based on map overlays Proceeding of International Association for Mathematical Geology Annual Meeting (IAMG 2001); 2001 Sep 10À12; Cancun, Mexico Garcıa M, Chuvieco E, Nieto H, Aguado I 2008 Combining AVHRR and meteorological data for estimating live fuel moisture content Remote Sens Environ 112:3618À3627 Downloaded by [203.128.244.130] at 00:53 15 March 2016 882 H.R Pourghasemi et al Giri S, Nejadhashemi AP 2014 Application of analytical hierarchy process for effective selection of agricultural best management practices J Environ Manage 132:165À177 Gokceoglu C, Sonmez H, Zorlu K 2009 Estimating the uniaxial compressive strength of some clay-bearing rocks selected from Turkey by nonlinear multivariable regression and rule-based fuzzy models Expert Syst 26:176À190 Hajeeh M, Al-Othman A 2005 Application of the analytical hierarchy process in the selection of desalination plants Desalination 174:97À108 Hernandez-Leal PA, Arbelo M, Gonzalez-Calvo A 2006 Fire risk assessment using satellite data Adv Space Res 37:741À746 doi:10.1016/j.asr.2004.12.053 Iwan S, Mahmud AR, Mansor S, Shariff ARM, Nuruddin AA 2004 GIS-grid-based and multi-criteria analysis for identifying and mapping peat swamp forest fire hazard in Pahang, Malaysia Disaster Prev Manage 13(5):379À386 Jaafari A, Najafi A, Pourghasemi HR, Rezaeian J, Sattarian A 2014 GIS-based frequency ratio and index of entropy models for landslide susceptibility assessment in the Caspian forest Northern Iran Int J Environ Sci Technol 11:909À926 Jager R 1995 Fuzzy logic in control [dissertation] Delft: Delft University of Technology Jaiswal RK, Mukherjee S, Raju KD, Saxena R 2002 Forest fire risk zone mapping from satellite imagery and GIS Int J Appl Earth Observ Geoinform 4:1À10 Janbaz Ghobadi Gh, Gholizadeh B, Majidi Dashliburun O 2012 Forest fire risk zone mapping from geographic information system in Northern Forests of Iran (case study, Golestan province) Int J Agric Crop Sci 4:818À824 Juang CH, Lee DH, Sheu C 1992 Mapping slope failure potential using fuzzy sets J Geotech Eng Div ASCE 118:475À493 Kayastha P, Dhital MR, De Smedt F 2013 Application of the analytical hierarchy process (AHP) for landslide susceptibility mapping: a case study from the Tinau watershed, west Nepal Comput Geosci 52:398À408 Koetz B, Morsdorf F, van der Linden S, Curt T, Allgower B 2008 Multi-source land cover classification for forest fire management based on imaging spectrometry and LiDAR data For Ecol Manage 256:263À271 Komac M 2006 A landslide susceptibility model using the analytical hierarchy process method and multivariate statistics in peri-alpine Slovenia Geomorphology 74:17À28 Krasnow K, Schoennagel T, Veblen TT 2009 Forest fuel mapping and evaluation of landfire fuel maps in Boulder County, Colorado, USA For Ecol Manage 257:1603À1612 Kurtener D, Badenko V 2000 Methodological framework based on fuzzy set theory for land use management J Braz Comput Soc 6:26À32 Kushla JD, Ripple WJ 1997 The role of terrain in a fire mosaic of a temperate coniferous forest For Ecol Manage 95:97À107 Langenbrunner JR, Hemez FM, Booker JM, Ross TJ 2010 Model choice considerations and information integration using analytical hierarchy process Proc Soc Behav Sci 2:7700À7701 Leuenberger M, Kanevski M, Vega Orozco CD 2013 Forest fires in a random forest Eur Geosci Union Gen Assembly 15:2013À3238 Maeda EE, Formaggio AR, Shimabukuro YE, Arcoverde GFB, Lima A 2009 Forest fire risk mapping in the Brazilian Amazon using MODIS images and artificial neural networks Int J Appl Earth Obs 11:265À272 Mamdani EH, Assilian S 1975 An experiment in linguistic synthesis with a fuzzy logic controller Int J Man Mach Stud 7:1À13 Mohammady M, Pourghasemi HR, Pradhan B 2012 Landslide susceptibility mapping at Golestan Province, Iran: a comparison between frequency ratio, Dempster-Shafer, and weights-of-evidence models J Asian Earth Sci 61:221À236 Nadeau LB, McRae DJ, Jin JZ 2005 Development of a national fuel-type map for Canada using fuzzy logic : INFORMATION REPORT NOR-X-406 Edmonton (AB): Canadian Forest Service Northern Forestry Centre Downloaded by [203.128.244.130] at 00:53 15 March 2016 Geomatics, Natural Hazards and Risk 883 Nandi A, Shakoor A 2010 A GIS-based landslide susceptibility evaluation using bivariate and multivariate statistical analyses Eng Geol 110:11À20 Nefeslioglu HA, Gokceoglu C, Sonmez H 2006 Indirect determination of weighted joint density (wJd) by empirical and fuzzy models: Supren (Eskisehir, Turkey) marbles Eng Geol 85:251À269 Nefeslioglu HA, Sezer EA, Gokceoglu C, Ayas Z 2013 A modified analytical hierarchy process (M-AHP) approach for decision support systems in natural hazard assessments Comput Geosci 59:1À8 Negnevitsky M 2002 Artificial intelligence: a guide to intelligent systems Harlow: Pearson Education; p 394 Noonan EK 2003 A coupled model approach for assessing fire hazard at point Reyes national seashore: Flam Map and GIS In: Second international wild land fire ecology and fire management congress and fifth symposium on fire and forest meteorology Orlando (FL): American Meteorological Society; p 127À128 Osna T, Sezer EA, Akgun A 2014 GeoFIS: an integrated tool for the assessment of landslide susceptibility Comput Geosci 66:20À30 Pierce AD, Farris GA, Taylor AH 2012 Use of random forests for modeling and mapping forest canopy fuels for fire behavior analysis in Lassen Volcanic National Park, California, USA For Ecol Manage 279:77À89 Pourghasemi HR, Goli Jirandeh A, Pradhan B, Xu C, Gokceoglu C 2013 Landslide susceptibility mapping using support vector machine and GIS at the Golestan Province, Iran J Earth Syst Sci 122:349À369 Pourghasemi HR, Moradi HR, Fatemi Aghda SM 2013 Landslide susceptibility mapping by binary logistic regression, analytical hierarchy process, and statistical index models and assessment of their performances, Nat Hazards 69:749À779 Pourghasemi HR, Pradhan B, Gokceoglu C 2012a Remote sensing data drived parameters and its use in landslide susceptibility assessment using Shannon’s entropy and GIS In: Varatharajoo R, Abdullah EJ, Majid DL, Romli FI, Mohd Rafie AS, Ahmad KA, editors Applied Mechanics and Materials (Volume 225) AEROTECH IV, Chapter 7: Space Systems p 486À491 Pourghasemi HR, Pradhan B, Gokceoglu C 2012b Application of fuzzy logic and analytical hierarchy process (AHP) to landslide susceptibility mapping at Haraz watershed, Iran Nat Hazards 63:965À996 Pourghasemi HR, Moradi HR, Fatemi Aghda SM 2014 GIS-based landslide susceptibility mapping with probabilistic likelihood ratio and spatial multi-criteria evaluation models (North of Tehran, Iran) Arab J Geosci 7(5):1857À1878 Pourtaghi ZS, Pourghasemi HR, Rossi M 2014 Forest fire susceptibility mapping in the Minudasht forests, Golestan province, Iran Environ Earth Sci http://dx.doi.org/10.1007/ s12665-014-3502-4 Pradhan B 2010a Use of GIS-based fuzzy logic relations and its cross application to produce landslide susceptibility maps in three test areas in Malaysia Environ Earth Sci 63(2): 329À349 Pradhan B 2010b Landslide susceptibility mapping of a catchment area using frequency ratio, fuzzy logic and multivariate logistic regression approaches J Indian Remote Sens 38:301À320 Pradhan B 2011 Manifestation of an advanced fuzzy logic model coupled with geoinformation techniques for landslide susceptibility analysis Environ Ecol Stat 18:471À493 Pradhan B 2013 A comparative study on the predictive ability of the decision tree, support vector machine and neuro-fuzzy models in landslide susceptibility mapping using GIS Comput Geosci 51:350À365 Pradhan B, Assilzadeh H 2010 Forest fire detection and monitoring using high temporal MODIS and NOAA AVHRR satellite images in Peninsular Malaysia Disaster Adv 3:18À23 Downloaded by [203.128.244.130] at 00:53 15 March 2016 884 H.R Pourghasemi et al Pradhan B, Lee S, Buchroithner MF 2009 Use of geospatial data for the development of fuzzy algebraic operators to landslide hazard mapping: a case study in Malaysia Appl Geomatics 1:3À15 Pradhan B, Suliman MDHB, Awang MAB 2007 Forest fire susceptibility and risk mapping using remote sensing and geographical information systems (GIS) Disaster Prev Manage 16:344À352 Prasad VK, Badarinath KVS, Anuradha E 2008 Biophysical and anthropogenic controls of forest fires in the Deccan Plateau, India J Environ Manage 86:1À13 Prosper-Laget V, Douguedroitl A, Guinot JP 1995 Mapping the risk of forest fire occurrence using NOAA satellite information EAR seL Adv Remote Sens 4:30À38 Rautela P, Lakhera RC 2000 Landslide risk analysis between Giri and Tons Rivers in Himachal Himalaya (India) Int J Appl Earth Observ Geoinform 2:153À160 Rawat GS 2003 Fire risk assessment for fire control management in Chilla forest range of Rajaji National Park Uttaranchal (India) [thesis] Enschede: International Institute for Geo-information Science and Earth Observation Razali SBM 2007 Forest fire hazard rating assessment in peat swamp forest using integrated remote sensing and geographical information system [thesis] Malaysia: University Putra Malaysia Regmi AD, Yoshida K, Pourghasemi HR, Dhital MR, Pradhan B 2014 Landslide susceptibility mapping along Bhalubang-Shiwapur area of mid-western Nepal using frequency ratio and conditional probability models J Mt Sci 11(5):1266À1285 Renard Q, Pelissier R, Ramesh BR, Kodandapani N 2012 Environmental susceptibility model for predicting forest fire occurrence in the Western Ghats of India Int J Wildland Fire 21:368À379 Rouse JW, Haas RH, Schell JA, Deering DW 1973 Monitoring vegetation systems in the Great Plains with ERTS (Earth Resources Technology Satellite) In: Freden SC, Mercanti EP, Becker MA editors Third earth resources technology satellite-1 Symposium- Volume I: Technical Presentations NASA SP-351; Washington (DC): NASA p 309À317 Saaty TL 1977 A scaling method for priorities in hierarchical structures J Math Psychol 15:234À281 Saaty TL 1994 Fundamentals of decision making and priority theory with analytic hierarchy process Pittsburgh: RWS Publications; p 527 Saaty TL 2000 Decision making for leaders: the analytical hierarchy process for decisions in a complex world Pittsburgh: RWS Publications Saaty TL, Vargas LG 2001 Models, methods, concepts and applications of the analytic hierarchy process Dordrecht: Kluwer Saboya FJ, Alves MDG, Pinto WD 2006 Assessment of failure susceptibility of soil slopes using fuzzy logic Eng Geol 86:211À224 Safi Y, Bouroumi A 2013 Prediction of forest fires using artificial neural networks Appl Math Sci 7:271À286 Saklani P 2008 Forest fire risk zonation, a case study Pauri Garhwal, Uttarakhand, India [dissertation] Enschede: International Institute for Geo-information Science and Earth Observation Shadman Roodposhti M, Rahimi S, Jafar Beglou M 2014 PROMETHEE II and fuzzy AHP: an enhanced GIS-based landslide susceptibility mapping Nat Hazards 73(1):77À95 Stojanova D, Panov P, Kobler A, Dzeroski S, Taskova K 2006 Learning to predict forest fires with different data mining techniques Proceedings of the Conference on Data Mining and Data Warehouses; 2006 Oct 9; Ljubljana, Slovenia; p 255À258 Teodoro AC, Duarte L 2013 Forest fire risk maps: a GIS open source application À a case study in Norwest of Portugal Int J Geogr Inf Sci 27:699À720 Tierno NR, Puig AB, Vera JB, Verdu FM 2013 The retail site location decision process using GIS and the analytical hierarchy process Appl Geogr 40:191À198 Downloaded by [203.128.244.130] at 00:53 15 March 2016 Geomatics, Natural Hazards and Risk 885 van Westen C 1997 Statistical landslide hazard analysis ILWIS 2.1 for Windows application guide Enschede: ITC Publication; p 73À84 Vargas LG 1990 An overview of the analytic hierarchy process and its applications Eur J Oper Res 48:2À8 Weise DR, Biging GS 1997 A qualitative comparison of fire spread models incorporating wind and slope effects For Sci 43:170À180 Whelan RJ 1995 The ecology of fire Cambridge: Cambridge University Press Wu CH, Chen SC 2009 Determining landslide susceptibility in Central Taiwan from rainfall and six site factors using the analytical hierarchy process method Geomorphology 112:190À204 Wulder MA, Franklin SE 2006 Understanding forest disturbance and spatial pattern: remote sensing and GIS approaches Boca Raton (FL): CRC Press (Taylor and Francis) Xiangwei G, Xianyun F, Hongquan X 2011 Forest fire risk zone evaluation based on high spatial resolution RS image in Liangyungang Huaguo Mountain Scenic Spot IEEE International Conference on Spatial Data Mining and Geographical Knowledge Services (ICSDM); 2011 Jun 29À2011 Jul 1; Fuzhou, China; p 593À596 Yager RR, Filev DP 1994 Approximate clustering via the mountain method IEEE Trans Syst Man Cybern 24:1279À1284 Yagiz S, Gokceoglu C 2010 Application of fuzzy inference and non-linear regression methods for predicting rock brittleness Expert Syst Appl 37:2265À2272 Yalcin A 2008 GIS-based landslide susceptibility mapping using analytical hierarchy process and bivariate statistics in Ardesen (Turkey): comparisons of results and confirmations Catena 72:1À12 Yesilnacar EK 2005 The application of computational intelligence to landslide susceptibility mapping in Turkey [dissertation] Melbourne: Department of Geomatics, The University of Melbourne; p 423 Youssef MA, Pradhan B, Tarabees E 2011 Integrated evaluation of urban development suitability based on remote sensing and GIS techniques: contribution from the analytic hierarchy process Arab J Geosci 4:463À473 Zadeh LA 1965 Fuzzy sets Inf Control 8:338À352 Zare M, Pourghasemi HR, Vafakhah M, Pradhan B 2013 Landslide susceptibility mapping at Vaz watershed (Iran) using an artificial neural network model: a comparison between multi-layer perceptron (MLP) and radial basic function (RBF) algorithms Arab J Geosci (8):2873À2888 Zhang R, Zhang X, Yang J, Yuan H 2013 Wetland ecosystem stability evaluation by using analytical hierarchy process (AHP) approach in Yinchuan Plain, China Math Comput Model 57:366À374 Zhao J, Zhang Z, Han S, Qu C, Yuan Z, Zhang D 2011 SVM based forest fire detection using static and dynamic features Comput Sci Inf Syst 8:821À841 ... prediction capabilities of modified analytical hierarchy process (M-AHP) and Mamdani fuzzy logic models using Netcad-GIS for forest fire susceptibility mapping HAMID REZA POURGHASEMIy*, MASOOD BEHESHTIRADz... Shariff ARM, Nuruddin AA 2004 GIS-grid-based and multi-criteria analysis for identifying and mapping peat swamp forest fire hazard in Pahang, Malaysia Disaster Prev Manage 13(5):379À386 Jaafari... vegetation index (NDVI) The spatial database for the study area is shown in table Table Data used for forest fire susceptibility mapping (FFSM) Data layers Data format Forest fire locations map