"The Potential of Cellulosic Ethanol Production from Municipal Solid Waste: A Technical and Economic Evaluation" doc

41 554 0
"The Potential of Cellulosic Ethanol Production from Municipal Solid Waste: A Technical and Economic Evaluation" doc

Đang tải... (xem toàn văn)

Tài liệu hạn chế xem trước, để xem đầy đủ mời bạn chọn Tải xuống

Thông tin tài liệu

Energy Development and Technology 015 "The Potential of Cellulosic Ethanol Production from Municipal Solid Waste: A Technical and Economic Evaluation" Jian Shi, Mirvat Ebrik, Bin Yang and Charles E. Wyman University of California, Riverside April 2009 This paper is part of the University of California Energy Institute's (UCEI) Energy Policy and Economics Working Paper Series. UCEI is a multi-campus research unit of the University of California located on the Berkeley campus. UC Energy Institute 2547 Channing Way Berkeley, California 94720-5180 www.ucei.org This report was issued in order to disseminate results of and information about energy research at the University of California campuses. Any conclusions or opinions expressed are those of the authors and not necessarily those of the Regents of the University of California, the University of California Energy Institute or the sponsors of the research. Readers with further interest in or questions about the subject matter of the report are encouraged to contact the authors directly. The Potential of Cellulosic Ethanol Production from Municipal solid waste: A Technical and Economic Evaluation Jian Shi, Mirvat Ebrik, Bin Yang*, and Charles E. Wyman Center for Environmental Research and Technology Bourns College of Engineering University of California Riverside, CA 92507 Tel: 951-781-5668 Fax: 951-781-9750 E-mail: binyang@cert.ucr.edu 1 Abstract Municipal solid waste (MSW) is an attractive cellulosic resource for sustainable production of transportation fuels and chemicals because of its abundance, the need to find uses for this problematic waste, and its low and perhaps negative cost. However, significant heterogeneity and possible toxic contaminants are barriers to biological conversion to ethanol and other products. In this study, we obtained six fractions of sorted MSW from a waste processing facility in Fontana, California: 1) final alternative daily cover (ADC Final), 2) ADC green, 3) woody waste, 4) grass waste, 5) cardboard, and 6) mixed paper. Application of dilute sulfuric acid pretreatment followed by enzymatic hydrolysis gave the highest sugar yields in cardboard and ADC final fractions at enzyme loadings of 100 mg enzyme protein/g sugars of raw materials. Treatment with our non-catalytic protein detoxification technology before adding enzymes improved sugar yields at low enzyme loading of 10 mg enzyme protein/g (glucan plus xylan) of raw materials. Pretreatment with 1% dilute sulfuric acid for 40 min followed by bovine serum albumin (BSA) supplemented enzymatic hydrolysis at an enzyme loading of 10 mg enzyme protein/g glucan recovered 79.1% of potential glucan and 88.2% of potential xylan in solution from ADC final, and 83.3% of potential glucan and 89.1% of potential xylan from ADC green. Experimental results were incorporated into an economic model to determine the economic feasibility of converting MSW to ethanol and identify opportunities for improving the economics. The minimum ethanol selling price for ADC final and ADC green was estimated as $0.6 per gallon and $0.91 per gallon, respectively. Keywords: municipal solid wastes, ADC final, ADC green, acid pretreatment, ethanol, lignin blocking, bovine serum albumin, Aspen model 2 Introduction Overcoming challenges of food supply, energy supply, and environment protection enables sustainable economic and social development(Lynd et al. 2008). In 2008, the world saw a stifling rise in fossil oil prices. In the United States, gasoline prices hit an all-time national average high, $4.11 per gallon, causing a surge of new research and a new consciousness in regards to the nation’s dependence on imported and domestic oil. One of the primary focuses within the U.S. biofuel research community has been on developing the processes that turn various sources of cellulosic biomass into bioethanol as an alternative transportation fuels, replacing gasoline and natural gas. The first generation fuel ethanol is derived from starch and sugar crops, such as corn, sugar cane, respectively. However, the long term availability and sustainability of these crops are questionable due to competition with the world’s food and animal feed supply. Thus, the second generation of bioethanol made from cellulosic feedstocks without a food use, namely cellulosic ethanol, has premise for a new industry, A broad range of lignocellulosic biomass has been considered as cellulosic ethanol feedstocks, including agricultural residues (e.g. corn stover, wheat straw), herbaceous energy crops (e.g. switchgrass, Miscanthus), and short-rotation forest crops (e.g. hybrid poplar and willow). Although conversion of cellulosic biomass to ethanol has been studied for decades, the uncertainty of techno-economic feasibility, particularly at large scale production, prohibits commercialization of such processes. Besides the relatively high cost of some processing stages (i.e. pretreatment and enzymatic hydrolysis), the cost of feedstocks share a large portion of operating costs. The NREL 2002 report projects that for a production scale of 2000 ton of feedstock per day, at $30/ton corn stover, feedstock costs 3 connect to 31.3% of the overall operating costs (Aden et al. 2002). At a larger scale of 5,000 tons of corn stover per day and a higher corn stover price of $40/ton, feedstock costs were estimated to account for 71.8% of the operating costs with advanced bioconversion processes (Lynd et al. 2005). On the other hand, using seasonally harvested feedstocks, such as agricultural wastes and energy crops, also raises questions of obtaining year-long supply or feedstock storage for large scale production. Therefore, lower feedstock costs along with achieving high yields of ethanol can result in significant improvements in the economics of cellulosic ethanol. A potentially low cost feedstocks is the municipal solid waste (MSW), but it is much less studied, specially the accurate cost-of-ethanol production data are unavailable (BR&Di 2008). Furthermore, MSW is the single largest source of cellulosic biomass in California. About 51.3% of MSW in California is cellulosic biomass, including construction and demolition wood (urban wood fuel), final alternative daily cover (ADC Final, landfill mulch), ADC green, woody and grass waste, cardboard, mixed paper and other minor biomass materials. The rich carbohydrate compositions of these cellulosic wastes, which amount to about 36.4 million tons per year, can provide a year round supply for ethanol production with zero to negative feedstock cost. Currently, a large portion of MSW is typically disposed of by incineration and/or landfill. However, environmental concerns about both options demand implementing alternative solid waste solutions. Public concerns on air pollution from incineration have halted construction projects of many new incinerators. In addition, the government, in reaction to problems associated with landfills, has mandated recycling to conserve natural resources and arrest of the flow of solid waste 4 into landfills (Green et al. 1990a; Laughlin et al. 1984; Li et al. 2007; Li and Khraisheh 2008). The 1989 Integrated Waste Management Act mandated local jurisdictions to divert at least 50% of waste from landfill by 2000(CaliforniaEnergyCommission 2007). In 2009, the state of California had not reached this target yet. There are urgent needs to investigate how to turn these solid wastes into beneficial products, especially energy products. MSW- based biofuels can “significantly reduce the greenhouse gas footprint and operating costs over the lifecycle of the biofuels supply chain” [DOE-EPA]. Clearly, MSW is an attractive cellulosic resource for sustainable production of transportation fuels and chemicals because it is an abundant and problematic waste that can be obtained at a low or perhaps negative cost (BR&Di 2008). The challenge is to achieve low cost conversion. The socioeconomic and environmental benefits of using MSW-derived ethanol continue to motivate great interests in research of process development. In addition, techno- economic evaluation of large scale bioconversion of MSW to ethanol is vital to defining its potential for commercialization. In this study, we investigated several types of MSW, including final alternative daily cover (ADC Final), ADC green, woody waste, grass waste, cardboard, and mixed paper. Most of these cellulose-hemicellulose rich wastes will end up landfilled if not utilized. Pretreatment is applied to break down hemicellulose into sugars and open up the structure of the remaining solids so that enzymes known as cellulases can breakdown the cellulose fraction to glucose with high yields in a subsequent enzymatic hydrolysis operation. Dilute acid pretreatment was employed to reduce the heavy metal content of the cellulosic component of municipal solid waste that can inhibit the following biological processes for ethanol production(Barrier et al. 1991; Johnson and Eley 1992; 5 Porteous 1972). In a leading application of this technology, the hemicellulose fraction is broken down or hydrolyzed with about 1% sulfuric acid at moderate temperatures of about 140-190 o C for times of about 10 to 20 minutes to release the hemicellulose sugars into solution (Lloyd and Wyman 2005; Mosier et al. 2005). Several other pretreatment methods, including alkali (Fontaine-Delcambe et al. 1986; Klee and Rogers 1977) and wet oxidation(Lissens et al. 2004a; Lissens et al. 2004b), were reported previously using MSW as feedstock. Sugars released from cellulose and hemicellulose can be fermented into ethanol. Alternatively, such sugars could be fermented into chemicals such as lactic acid or chemically reacted into products such as levulinic acid (Lloyd and Wyman 2005; Wyman et al. 2005a; Wyman et al. 2005b). The biggest challenge is that a sustainable portion of MSW is un-convertible to ethanol by bioconversion process or toxic to enzymes and microorganisms (Chieffalo and Lightsey 1995; Chieffalo and Lightsey 1996; Grace et al. 1994; Hoge 1982; Lightsey and Chieffalo 1995). This often leads to low digestibility of pretreated solids, high enzyme loadings and/or low fermentability. Questions about suitability of the feedstock and the process can present serious impediments to commercialization of ethanol production from MSW. In addition, the lack of techno- economic information is a major drawback for technology development and applications. In order to overcome the challenges, we assessed the technical and economic feasibility of converting the cellulosic biomass fraction in California MSW to ethanol at a low cost. Our first objective is to characterize major biomass components in representative sources of California MSW and determine the technical performance for cellulosic ethanol production via applying leading technologies for biomass pretreatment coupled with 6 enzymatic digestion using our established non-catalytic protein blocking techniques. Based on experimental data, our second objective is to assess the economic feasibility of using California MSW for the production of low cost fuel-grade ethanol at a commercial scale. Previously developed techno-economic models of corn stover ethanol processes were adapted to bioconversion of MSW to ethanol to project production costs and define opportunities for improvement. Materials and Methods Feedstock Preparation Six types of cellulose-rich municipal solid wastes, including final alternative daily cover (ADC Final), ADC green, woody waste, grass waste, cardboard, and mixed paper, were collected from the West Valley Material Recovery Facility and Transfer Station (Fontana, CA) during summer seasons of two consecutive years (July 2007 and August 2008). The Transfer Station serves 3 out of 13 cities in Riverside and San Bernardino County. Upon receipt, MSW samples were cleaned by soaking in DI water, and the top portions were decanted off to leave apparent dirt and rocks on the bottom. The cleaned MSW portions were air dried, milled to pass through a 2 mm screen by a Model 4 Thomas Wiley Laboratory Mill (Thomas Scientific, Philadelphia, PA), mixed well, and stored sealed at -18 ºC until use. Pretreatment Prior to pretreatment, MSW samples were presoaked overnight in 1% w/w dilute sulfuric acid solution at room temperature. All pretreatments were conducted in a 1 L Hasteloy Parr reactor with a total reaction volume of 800 ml at 5% dry w/v solid loading. 7 Biomass slurries were stirred at 200 rpm with two stacked pitched blade impellers (diameter 40 mm). MSW samples were pretreated with 1% w/w H 2 SO 4 at 140 °C for 40 min corresponding to a combined severity of 2.1. The combined severity factor ( 0 'log R ) is defined by the following as a function of the pretreatment temperature T (°C), pretreatment time t (min), and pH value: pHetR T −⋅= − )log('log 75.14 100 0 (1) The reactor was heated to reaction temperature using two sand baths: the first set to temperature of 320 °C for rapid heat up to the target temperature, and the second set at a 2 °C higher than the target temperature to maintain the pretreated temperature. The heat up time for this system varied between 1 to 3 min and was not included in the stated reaction times or the severity calculation. The temperature was measured inside the reactor using a Type K thermocouple. After pretreatment, the reactor was submerged in a room temperature water bath until the temperature dropped to 80 °C (the cooling time is around 2 min). The slurry was filtered immediately afterwards with the temperature being always higher than 60 °C. Pretreated solids were washed with 1.5 L DI water at room temperature (Yang and Wyman 2002). Analytical Methods Total solids, ash, acid insoluble lignin and carbohydrate (glucan and xylan etc.) contents of untreated and pretreated MSW fractions were determined following NREL Laboratory Analytical Procedures, LAP 001, LAP 003, LAP 004 (Ehrman 1996; Ehrman 1994a; Ehrman 1994b; Templeton and Ehrman 1995). Solid recovery was calculated as a [...]... garbage bins as potential fuel ethanol production feedstocks for further technical assessment Among these six types of MSW, including final alternative daily cover (ADC final), ADC green, woody waste, grass waste, cardboard, and mixed paper, ADC final and ADC green are MSW fractions that extract a tipping fee for landfilling, providing zero to negative feedstock costs Woody wastes and grass wastes are... grass wastes Among these fractions, ADC final and ADC green are the fractions that will be sent to landfills with the median average tipping fee of $36 if not utilized According to California regulations, ADC final and ADC green will be prohibited from landfills in the near future Besides ADC final and ADC green, woody wastes and grass wastes are also low cost cellulose-rich materials, with prices of. .. the overall yield of xylan and glucan for ADC final reached 79.1% and 88.2%, respectively The overall yield of xylan and glucan for ADC green was 83.3% and 89.1%, respectively, through pretreatment and enzymatic hydrolysis at 10 mg enzyme protein/g sugars of raw materials, and treated with 0.2% wt/v BSA Based on the technical assessment as described above, experimental data was adapted into the NREL... prepare fuel ethanol feedstocks Certainly, with additional mechanical and manual operation, more cellulosic materials can be recovered from black bin wastes Figures 1 and 2 show how wastes from blue and green 12 bins are separated, recycled, and disposed of For this project, we considered further investigation of six MSW fractions, including mixed paper, cardboard, ADC final, woody waste, ADC green, and. .. such as paper, cardboard, plastic, glass and cans, while that from green bins contains grass and woody wastes Comparing with MSW from black bins, which contains un-sorted residential and commercial wastes, MSW from blue and green bins are more readily for bioconversion to fuel ethanol because it not only contains cellulose and hemicellulose rich materials but also requires less labor and operations... mixed paper Thus, large amount of impurities in raw ADC final, grass waste, woody waste and cardboard was removed after pretreatment probably because of the solubilization of organics in pretreatment filtrate Table 2 Dilute acid pretreatment of MSW @ ADC final Solid Solid Recovered, % Glucan, %dw Xylan, %dw Lignin, %dw Ash, % dw Other, %dw Overall Xylan removal, % * Lignin removal, %* Grass wastes Woody... xylan (X) 5 (b) Sugar release summary for ADC green under optimal conditions 24 Economic analysis of ethanol production from MSW The lab research results indicated that low cost ADC final and ADC green were among the best feedstocks for fuel ethanol production because of high sugar yields at low enzyme loadings In order to evaluate the techno -economic feasibility of MSW (e.g ADC final and ADC green) bioconversion... second abundant polysaccharide in plant cell wall, usually constitutes about 20-35% of the plant materials (Wyman et al 13 2005c) However, the xylan content of collected MSW fractions was only about 5-10% The amount of other carbohydrates, such as mannan, arabinan and galactan, was negligible Lignin, which strengthens cellulosis biomass structure by holding cellulose and hemicellulose together (Ragauskas... enzymatic hydrolysis of ADC final and ADC green was investigated at levels of 0.08-0.32 v /v (Novozyme 188 to Spezyme CP) at a fixed Spezyme CP loading of 10 mg/g total glucan and xylan in the raw biomass and at a fixed total enzyme protein loading of 10 mg/g total glucan and xylan in the raw biomass BSA Treatment Prior to Enzymatic Hydrolysis In order to test the effectiveness of protein detoxification,... industrial hazardous wastes MSW can be categorized into five groups: 1) biodegradable waste, such as food and kitchen waste, green waste, paper; 2) recyclable material, such as paper, glass, bottles, cans, metals, certain plastics, etc.; 3) inert waste such as construction and demolition waste, dirt, rocks, debris; 4) composite wastes such as waste clothing, Tetra Paks, and waste plastics such as toys; . The Potential of Cellulosic Ethanol Production from Municipal solid waste: A Technical and Economic Evaluation Jian Shi, Mirvat Ebrik, Bin Yang*, and. glucan recovered 79.1% of potential glucan and 88.2% of potential xylan in solution from ADC final, and 83.3% of potential glucan and 89.1% of potential

Ngày đăng: 09/03/2014, 00:20

Từ khóa liên quan

Mục lục

  • EDT015.pdf

    • Materials and Methods

      • Feedstock Preparation

      • Pretreatment

      • Analytical Methods

      • Enzymatic Hydrolysis

      • BSA Treatment Prior to Enzymatic Hydrolysis

      • Experimental Design and Statistical Analysis

      • Results and Discussions

        • Cellulosic MSW Feedstocks

        • Compositions of raw MSW fractions

        • Dilute acid pretreatment of MSW

        • Digestibility of pretreated MSW fractions

        • Effects of BSA treatment and enzyme loadings on digestibility

        • Sugar release summary at optimal conditions

        • Economic analysis of ethanol production from MSW

        • Conclusions

        • Acknowledgements

        • Reference

Tài liệu cùng người dùng

  • Đang cập nhật ...

Tài liệu liên quan