Electronics and Circuit Analysis Using MATLAB P1

... Okyere. Matlab Fundamentals.” Electronics and Circuit Analysis using MATLAB. Ed. John Okyere Attia Boca Raton: CRC Press LLC, 1999 © 1999 by CRC PRESS LLC CHAPTER ONE MATLAB FUNDAMENTALS MATLAB ... additional MATLAB commands to get one started on MATLAB. Detailed descriptions and usages of the commands can be obtained from the MATLAB help facility or from MATLAB manuals. Table 1.2 Some Basic MATLAB ... 15; 18] MATLAB is case sensitive in naming variables, commands and functions. Thus b and B are not the same variable. If you do not want MATLAB to be case sensitive, you can use the command casesen...

Tài liệu Electronics and Circuit Analysis Using MATLAB P12 pdf

... characteristics and the locus that separates triode and saturation regions are obtained using MATLAB. Example 12.6 For an n-channel enhancement-type MOSFET with kmAVn=12/ and VV=15., ... The sensible and possible root is the one that will make VVGS T> The MATLAB program for finding ID is shown below. MATLAB Script % % Analysis of MOSFET bias circuit % ... The midband gain, Am, is obtained from the midband equivalent circuit of the common-source amplifier. This is shown in Figure 12.24. The equivalent circuit is obtained by short-circuiting...

Tài liệu Electronics and Circuit Analysis Using MATLAB P11 doc

... Attia, John Okyere. “Operational Amplifiers.” Electronics and Circuit Analysis using MATLAB. Ed. John Okyere AttiaBoca Raton: CRC Press LLC, 1999 ... MATLAB script % Frequency response of op amp % poles are p1 = 400*pi; p2 = 8e5*pi; p3 = 1.6e6*pi; p = [p1 p2 p3]; % zeros z = [0]; const = 2.62e21; % convert to poles and zeros and ... amplifier is at 200 Hz and the gain is - 500. The pole of the voltage amplifier and level shifter is 400 KHz and has a gain of 360. The pole of the output stage is 800KHz and the gain is 0.92....

Tài liệu Electronics and Circuit Analysis Using MATLAB P10 ppt

... Attia, John Okyere. “Semiconductor Physics.” Electronics and Circuit Analysis using MATLAB. Ed. John Okyere AttiaBoca Raton: CRC Press LLC, 1999 ... the conduction band EV = energy in the valence band and k, T, mn* and mp* were defined in Section 10.1. In an intrinsic semiconductor (Si and Ge) mn* and mp* are ... direct band gap semiconductor. The energy levels of the outer electrons form energy bands. In insulators, the lower energy band (valence band) is completely filled and the next energy band (conduction...

Tài liệu Electronics and Circuit Analysis using MATLAB P1 ppt

... of electrical and electronic circuits and systems. Organization The book is divided into three parts: Introduction to MATLAB, Circuit analysis applications using MATLAB, and electronics ... Attia, John Okyere. Electronics and circuit analysis using MATLAB / John Okyere Attiap. cm.Includes bibliographical references and index.ISBN 0-8493-1176-4 (alk. paper)1. Electronics Data processing. ... 1.2 shows additional MATLAB commands to get one started on MATLAB. Detailed descriptions and usages of the commands can be obtained from the MATLAB help facility or from MATLAB manuals. Table...

Electronics and Circuit Analysis Using MATLAB

... Figure P4.6 Circuit for Exercise 4.6 © 1999 CRC Press LLC © 1999 CRC Press LLC Attia, John Okyere. “Transient Analysis. ” Electronics and Circuit Analysis using MATLAB. Ed. John ... Ohms12 Ohms3 OhmsRL36 V Figure P4.5 Circuit for Exercise 4.5 © 1999 CRC Press LLC © 1999 CRC Press LLC 4.6 Using loop analysis and MATLAB, find the loop currents. What is the ... CHARACTERISTICS 9.1.1 Forward-biased region 9.1.2 MATLAB function polyfit 9.1.3 Temperature effects 9.2 ANALYSIS OF DIODE CIRCUITS 9.3 HALF-WAVE RECTIFIER 9.3.1 MATLAB function fzero 9.4 FULL-WAVE RECTIFICATION...

Electronics and Circuit Analysis Using MATLAB P3

... Attia, John Okyere. “Control Statements .” Electronics and Circuit Analysis using MATLAB. Ed. John Okyere AttiaBoca Raton: CRC Press LLC, 1999 ... = 3.4 INPUT/OUTPUT COMMANDS MATLAB has commands for inputting information in the command window and outputting data. Examples of input/output commands are echo, input, pause, keyboard, ... keyboard, break, error, display, format, and fprintf. Brief descriptions of these commands are shown in Table 3.3. Table 3.3 Some Input/output Commands COMMAND DESCRIPTION break exits while...

Electronics and Circuit Analysis Using MATLAB P2

... Attia, John Okyere. “Plotting Commands.” Electronics and Circuit Analysis using MATLAB. Ed. John Okyere AttiaBoca Raton: CRC Press LLC, 1999 ... the x- and y-axes, and add a grid to graphs. In addition, there are commands for controlling the screen and scaling. Table 2.1 shows a list of MATLAB built-in graph functions. One can use MATLAB s ... Plots of x2 and x3 using Subplot Commands. The coordinates of points on the graph window can be obtained using the ginput command. There are two forms of the command: [x y] = ginput...

Electronics and Circuit Analysis Using MATLAB P6

... Attia, John Okyere. “AC Analysis and Network Functions.” Electronics and Circuit Analysis using MATLAB. Ed. John Okyere AttiaBoca Raton: CRC Press LLC, 1999 ... power and quadrature power. Three-phase circuits are analyzed by converting the circuits into the frequency domain and by using the Kirchoff voltage and current laws. The un-known voltages and ... compute the vector [v] using the MATLAB command ()VinvYI=* where ()inv Y is the inverse of the matrix []Y. A MATLAB program for solving V3 is as follows: MATLAB Script ...

Electronics and Circuit Analysis Using MATLAB P5

... Attia, John Okyere. “Transient Analysis. ” Electronics and Circuit Analysis using MATLAB. Ed. John Okyere AttiaBoca Raton: CRC Press LLC, 1999 ... VsR1R3R2C1C2LV1V2I1y(t)+++ - Figure 5.11 Circuit for State Analysis Using the above guidelines, we select the state variables to be VV12,, and i1. Using nodal analysis, we have © 1999 CRC ... equation % Its m-file is diff1.m % % Transient analysis of RC circuit using ode % function and analytical solution % numerical solution using ode t0 = 0; tf = 20e-3; xo = 0; % initial...

Xem thêm