high-tech practical jokes for the evil genius

... surface of the device, and then once the power is removed from the motor, the other nutwill drop and strike the surface, creating the beatof walking feet. In my unit, one side of the arm isabout ... and the other is about 2 inches. The center of the copper wire is wrapped around the motor shaft and then held securely with a bit ofsolder on the wire and motor shaft. The surface that the ... 212Index 221xii51 High-Tech Practical Jokes for the Evil Genius This page intentionally left blank IntroductionChapter 1Warranty void!This book was written for all those who feel the irresistible...

101 spy gadgets for the evil genius

...

Electronic circuits for the evil genius

...

Tài liệu 15 Dangerously Mad Projects for the Evil Genius ppt

... program the Arduino■A USB-type A-to-B lead (as used for printers)TOOLBOX86 15 Dangerously Mad Projects for the Evil Genius The stripboard layout for the LED moduleFigure 8-5Step 2. Solder the ... all the cables are attached, it only remainsto solder a wire for the ϩ5V supply to the stripboard. We used solid core wire attached to the back of the stripboard for this. The other end of the wire ... canskip these sections.Installation on Mac OS X The process for installing the Arduino software on the Mac is a lot easier than on the PC.As before, the first step is to download the file.In the...

30 Arduino Projects for the Evil Genius doc

... breadboard. The software for all the projects is available for download from www.arduinoevilgenius.com.Without Further Ado The Evil Genius is not noted for their patience, soin the next chapter ... browse towww.arduinoevilgenius.com and click Downloadsat the top of the screen.6 30 Arduino Projects for the Evil Genius Setting the serial port on the Mac.Figure 1-11Setting the serial port ... X The process for installing the Arduino software on the Mac is a lot easier than on the PC.4 30 Arduino Projects for the Evil Genius Windows Found New HardwareWizard.Figure 1-6Setting the...

208
1,311
1

electronic circuits for the evil genius docx

... needed for the work being done on the construction shown here. The Parts Bin on the following page has the complete parts list used inPart One. These are pictured in the front of the book in the ... Electronic Circuits for the Evil Genius is based on practical projects thatexercise the genius that exists in all of us. Components are introduced as you buildworking circuits. These circuits are ... and other mumbo jumbo. Look for the information that specifically lists 1 μF, 10 μF, 100 μF, and 1000 μF.There is another capacitor of a different shape tolocate. Figure L1-8 shows the other...

radio and receiver projects for the evil genius

... moves to the mixer stage. Notice on the diagram that there are twoinputs to the mixer. We have discussed one of these inputsignals coming into the mixer but not the other. Now,look down at the ... receiver. The antenna is sent to the RFamplifier. The mixer is fed by both the local oscillatorand the RF amplifier. The signal from the mixer is sentto a bandpass filter and then on to the first ... high the waves are coming intoshore from the ocean. The bigger wave has a higheramplitude. The other thing is frequency. Frequency ishow often the wave occurs at any point. The faster the wave...

science fair projects for the evil geniusg

... Projects for the Evil Genius piece of rope through the handles on the other bag.Tie a long piece of string onto a heavymetal washer. From a child’s backyard swingset, tie the other end of the ... hot. The incandescent bulbin the desk lamp should be about 60 or 75watts. The heat from the bulb may drive anyinsects down into the glass, as they try toescape the heat. Leave the bulb on for ... jar.Then, set the nest in the mouth of the funnel.Position a desk lamp over the top of the nest,but keep a space of several inches between the lamp’s bulb and the nest to prevent the nest from...

green projects for the evil genius

... it gathers water as the moving stream turns the wheel. As the wheel turns with the spiral attached to it, the spiral gathers waterduring the first half of the rotation, then air during the second ... leaks.21. Then, to begin putting your inner tube back onto the rim, line up the valve with the hole in the rim andpush it through (Figure 2-19).50 Green Projects for the Evil Genius 22. Place the ... free of the rim.9. Reach into the tire and feel the inner tube, find the valve (see Figure 2-10) and gently pull it out of the hole in the rim. Then you can remove the tube frominside the tire...

model rocket projects for the evil genius

...

Xem thêm